fs ia6b 3d models

This item is a protective cover designed specifically for FlySky FS-GT3B batteries. Its compact fit ensures secure battery storage at all times. Printing recommendations include using settings below 0.2 to accommodate the guide rails present on each...

This general mount is designed to be easily attached to your FlySky FS-GT3B RC remote using the two front screws. It serves as a mobile phone holder for recording videos while operating your RC car. Please be aware that there was an error in scale...

Its a TBS module adapter for fs-i6 controller. Two versions available: one with angled top to fit TBS antenna a bit better. 6 pin header from TBS PCB should be cut (de-soldering is tough due to close smd parts). Adapter is fixed to the controller...

Basic Phone Clamp Designed for Flysky RC Transmitter (FS-GT5). May Also Fit Other Models, Utilizing M4 Nuts and Bolts with an Added M4 Thumbscrew for Quick Clamping and Easy Angle Adjustment. Enables Hands-Free Filming of Your RC Vehicles. For...

This is a set of grips I designed for the flysky fs-i6 because the radio felt kinda small because I have bigger hands. So if you have bigger hands like me then these will add about 1cm to each side of the radio. ...You just have to stick it to the radio...

Didn't like the way the metal bits on the Flysky FS-I6 feel so I designed and 3D printed some adapters that go on top and screw on to the gimbals using the M3 bolts on it. There are 2 versions. one that uses an M3 nut to ensure it doesnt come...

The filament-sensor cover (FS-cover) is a part where you insert the filament into the extruder. Some people reworked it for inserting a Festo connector, but this all did not work out for me. So I re-designed this Thing (org. Prusa) to have a longer...

This mount system allows you to attach phones, cameras, lights, microphones, and anything else that uses either a 1/4" camera mount or a cold shoe camera mount to your Flysky FS-GT5. ... Non-3D printed parts also needed: 3-1/2" 1/4-20...

... right. After some investigation, I concluded that the FS lever was the culprit. It didn't seem to be moving far enough to trigger the IR sensor, so I made a modification to the lever by adding about 1mm to its end. The result? ...IT NOW WORKS!!!

replacement back for the FlySky FS-T6 transmitter Print Settings Printer Brand: RepRap Printer: metal Rafts: No Supports: Yes Resolution: 0.1mm Infill: 100% Category: Hobby

Didn't like the way the metal bits on the Flysky FS-I6 feel so I designed and 3D printed some adapters that go on top and screw on to the gimbals using the M3 bolts on it. There are 2 versions. one that uses an M3 nut to ensure it doesnt come lose...

... the plastic to see if it self-taps. I'm currently working on a skirt that you can glue 11mm paintballs into to make FS-like mini rounds. Print, test, and enjoy! Don't forget to leave your suggestions, comments, and feedback. ...**More to come!**

... Remote, I use a hook-and-loop fastener. Note: I bonded the frame halves with superglue. Issues: The hole for the teacher/simulator plug is on the wrong position. I cut the bottom on the right position. You don't need to print the FS-i6X model.

I've searched for a GoPro-Mount for my Dye Proto FS Fullface-Mask, but didn't found something, so I created a mount by myself. If you did a print: Please post a "i've made one" and share your experience on the comments-tab! and if you like my...

Power transfer of FLYSKY FS-i6 (FLYSKY FS-i6x) equipment to power from 18650 batteries (2x). Mini version with parallel connection of 2 x 18650 batteries. Without untwisting and interference in the middle of the equipment. When using, monitor the...

The PSU connector for the Panasonic FS-A1 and Sony HB-F1 computers has a strange mini-iec connector (as does the NEO GEO CD). ...This is a replacement for it, you'll need to put come metal tubes inside the holes and connect it to a suitable PSU (a...

This is a meticulously designed to-scale layout of the FS-BS6 receiver. I built a custom containment unit to waterproof it for my RC car, and thought it was worth uploading along with some extra details. As always, I've included the SKP file for...

This is a custom-designed gimbal protector for the FlySky FS-I6, precision-crafted to fit perfectly within its gimbals. While current versions may not stay locked in place, future iterations promise to provide a snug and secure fit. The latest...

Power transfer of FLYSKY FS-i6 (FLYSKY FS-i6x) equipment to power from 18650 batteries (2x). Mini version with parallel connection of 2 x 18650 batteries. Without untwisting and interference in the middle of the equipment. When using, monitor...

I chose to create a custom battery cover for my Flysky FS-i6 that enables me to utilize a single rechargeable 18650 battery stick. By incorporating USB functionality, I made the design even more versatile since I can now power it with any USB-enabled...

I'm hoping .50 cal will make the marker more practical. I am working on making a conversion kit for the Kingman Eraser/Chaser to be able to shoot a FS-like round. None of this stuff has been tested or even yet printed for that matter. The magazine...

... I'm currently working on a skirt that you'll be able to glue your 11mm paint balls into to make the FS-like mini rounds. Print, test, enjoy! Don't forget to leave your suggestions comments and feed back.More to come! ... Category: Sport & Outdoors

Tuning Bolt for FS T15Tested on T15 with Cocker Sleeve and Dynamic Sports Gear T15 Power Tube.The components uploaded here do not fit the standard bolt and bulkhead.Only the Striker and Striker components can be used from the standard system.Barrle...

Phone and drone telemetry mount (SiK/3DR/Holybro, hole cross section 26mm x 12mm) for a FS-i6 (FlySky i6/i6X) remote and others. The remote mount has various mounting holes for maximum compatibility. To get it fixed tightly, use the correct size nut...

FAQ: http://www.thingiverse.com/shivinteger/about Generating Attributions log: Thing Title : Kitten Thing URL : http://www.thingiverse.com/thing:12694 Thing Author : MBCook Thing Licence : Creative Commons - Attribution - Share Alike Thing Title :...

FS RIALTO

This model was crafted using Tinkercad. ...Refine it now at https://www.tinkercad.com/things/9pLr2xXwqJd.

I chose to give it a shot and went with the two-sided approach instead.

A person is sitting there.

*Keyence*Amplifier*Main Unit