frsky r xsr 3d models

30.5 x 30.5 inch mount plate secures the IRC Tramp at the top and the Frsky XSR at the bottom, tightly held in place with two sturdy zip ties. ...This versatile setup stacks neatly atop the Flight Controller (FC), providing a stable base for your aerial...

This is an all-in-one antenna holder and R-XSR mount designed to fit snugly over the standoffs of the MiniRaceWing FPV race wing from Flybot.de. ...The R-XSR antennas benefit greatly when wrapped with shrink tube and secured in place using a zip tie for...

A premium plate Frsky X-XSR chip mount for GEPRC Hummingbird drone. To assemble it, you will need to acquire 3 M2 x 0.4 x 12mm socket head screws. Print the top down and add supports to the countersinks. ... Eric is not my concern.

A tiny bracket is needed to secure an R-XSR to the rear standoffs. ...Wrap a compact cable tie around the hole, then seal it with heatshrink tubing as you connect the antenna.

This is a straightforward R-XSR sized receiver mount featuring built-in antenna provisions and stabilizing support for the rear arms of the drone, designed to prevent movement after a crash. ...This component is specifically intended for use with the...

The R-XSR receiver and TX805 VTX holder uses two 3mm antenna tubes on the Martian II frame. To ensure durability, I reinforced the tube holders with heatshrink. ...After printing, drill 5mm corner holes using a drill bit, then tap M3 threads in the...

... tapping into place using an M3 screw, be careful not to go too fast or the material will heat up and distort. Check out this link for more info: https://www.rcgroups.com/forums/showthread.php?2972644-20x20-micro-swift-vtx03-r-xsr-pod#post38453043

I also required a secure spot for my R-XSR. The print quality was subpar, and the bed wasn't leveled properly. However, it still managed to serve my purposes. For those who want to make adjustments, I've attached the SCAD files. ... Update: I've...

Mount the Unify Pro HV + R-XSR + AXII on the XL5 by attaching all components outside of the frame and placing the holle unity inside. To achieve a lightweight design, print this model in Flex material such as TPU using a 0% infill rate. A lighter...

The FrSky XSR-M/XSR-E mount is areaaaallly tiny receiver (20x20 mm in size with 15x15 mounting), having 16 channels and telemetry. Since I couldn't find a suitable mount/adapter for it (in combination with my frame), here's this little mount...

The FrSky XSR-M/XSR-E mount is a teeny receiver (20x20 mm in size with 15x15 mounting), boasting 16 channels and telemetry. Since I couldn't find a suitable mount/adapter for it (in combination with my frame), here's this little mount which can be...

Tiny XSR mount securely attaches via precision-crafted holes for effortless zip tie installation, ensuring optimal airflow throughout. ...Effortlessly stick it to any frame using ultra-strong double-sided tape for a rock-solid hold.

The FrSky XSR-M/XSR-E mount is an incredibly compact receiver measuring just 20x20 mm with a 15x15 mm mounting area, boasting an impressive 16 channels and telemetry capabilities. Due to the unavailability of a suitable mount or adapter for this...

Holder for Frsky Rxm receiver. ...Compact design suitable for micro drones, features 20x20mm mounting holes.

Apply several drops of high-strength adhesive directly to the assembly points and quickly join the components together, ensuring a secure bond forms immediately.

Emax Tinyhawk II Freestyle r-xsr (xsr, xm, xm+) antenna mount to back

Rugged TBS Source One R-XSR and VTX Mount System.

This little mount is specifically designed for the R-XSR receiver from FrSky, and it's meant to sit right next to a Matek VTX-HV. It features a tiny spot where you can secure the VTX antenna pigtail using a zip tie, giving you extra stability. ...While...

... Protective mount designed for the FrSky R-XSR and its 2 antennae. A better solution was needed than just zip-tying the antennae to arms or using heat shrink. One small zip-tie secures the RX into the mount, while two zip-ties mount it to the frame.

... Protective mount for the FrSky R-XSR and it's 2 antennae. Needed a better solution than just zip tying the antennae to the arms / heat shrink etc. Used 1x small zip-ties to secure the RX into the mount, and 2x zip-ties to mount it to the frame.

The antenna mount is specifically designed for use with a standard 20 x 20 inch heat shrink tubing to provide extra stability and secure positioning of the antennas.

I'm not sure what that means. ...Can you try again?

Things must link up securely on the standoffs of your helicopter. No additional tightening is required. ...Your system is shielded from impacts caused by propellers.

Human beings require robust protection from various hazards and risks that they face on a daily basis. The primary goal of human protection is to safeguard their well-being and safety, ensuring that individuals can navigate their environment without...

I'm operating a Martian 215 rear stock 20x20 paired with an R-XSR holder, utilizing a misplaced beeper configuration.

The R-XSR receiver and UNIFY NANO video transmitter mounting plate is specifically designed to fit standard 30.5 by 30.5 stack sizes.

Another fancy 2020 to 3030 adapter for your fpv frame stack, plus an frsky r-xrs holder

This is a second version after https://www.thingiverse.com/thing:4584768, which adds VTX antenna mount holder. ...It is not a remix was redesigned from scratch with a better fit for R-XSR receiver

Mounting the R-XSR receiver directly onto the tooth fairy frame seemed like the most logical place, eliminating the need for sticky tape that can damage the equipment. After surviving its first landing in tall grass, which transformed the...

R-XSR is mounted the way leds will be visible. For SMA it's better to use pigtail. Xt30 plug is directed inwards for compactness. Project can be updated later, I'm planning to add some SMA protection on the bottom. XT30 can be rotated a...