frsky horus x10 3d models

... modification, used with permission. ... This thing was designed to enable the installation of a LiPo transmitter pack into the FrSky Horus X10 without any permanent modifications to the case. This project is detailed on RCGroups at the link below.

The original Horus 10 / 10s has a sturdy metal holder, providing robust protection for the antenna on its external module. However, for users without an external module or one lacking an external antenna, this holder may appear oversized, hindering...

Horus X10 battery life is already limited, but for those flying long distance with the R9M, it becomes even more of an issue. Factor in running Yappu hud lua on opentx, display full bright in the sun, haptic feedback and so forth, this excellent...

It was annoying to me to see how the Zipp 9 antenna is moving while moving with Horus X10 Tx. So I prepared a simple holder for such kind of antenna. It's then clamped to original Tx holder. ... After necessary parts are printed, only 4 pcs of M4x10 (or...

It uses a spare Frsky stick-end on a 25mm M4 stud (you have to tap the hole - it should be 3.3mm dia ready for tapping) but you could make something selse that glues or screws in if you prefer. I used the stick-ends partly because my previous...

There are two versions of this protector available. ... -The standard version is a 30mm protector, represented by the file "horusx10stickprotector.stl." -A raised version is also available, featuring a 37mm design and denoted by the file name...

This is the revised balancer (version 4), significantly upgraded and precisely tailored to meet the demands of the M3 12mm inbus system. Strategically positioned at the top of the hole, it leaves a substantial amount of material underneath, thereby...

FrSky Horus X10s Battery Tray holds four high-capacity 18650 Li-ion cells. The tray is specifically designed to accommodate these larger cells, providing a secure fit that helps maintain optimal battery performance. ... The original protective board...

This adapter is placed between the gimbal and the casing (using longer screws) to position the gimbals further within the casing. This setup provides a more ergonomic shape for thumb pilots. For additional details on installation, refer to my post on...

I snapped a switch, yanked it out, and was left with an opening that needed covering up. You can use a pretty versatile type of filament for this job. ... FreeCAD project files have been included, so you're free to adjust them however suits your...

This is a remix of well designed protector (see source). ...After some time of using it, I designed couple of changes: - The heigth of gimbal protectors increased - The heigth of whole protector decreased - Needs about 1/3 less material - Gimbal...

Simply print the tray incl. 4 spacer and glue the spacer to the tray. ... I use Samsung 50E 5000mAh

Transmitter sticks with M4 tread. ...Originally created for Frsky Horus X10, but they can be used with any transmitter with M4 tread sticks. ...Treads need to be drilled by hand.

This is a replacement battery cover for a FrSky Horus X10/X10S Express. The Express is the version with the Access firmware and has a battery door. The first generation Horus X10/X10S did not have a back which supported a battery cover (however, you...

Transmitter Tray HORUS X10 to print in 3D.

The FrSky Horus X10S Monitor Mounting Bracket provides easy installation for pilots. This bracket offers versatile mounting options at both the bottom and rear of the device. Installation is straightforward, as it simply screws onto the rear handle...

This is a Tray for the Horus X10 radio. You can print it in any material you choose, I recommend using TPU(or some type of flexible material for any thing you see printed in orange in the photos. Some of the prints need to be printed multiple...

Handlebar for a frsky Horus x12s. ...

Long-range antenna rods are ideal for use with the FrSky Horus TX transmitter.

Quick remix of this. ...Original hole clearance was not sized for the X10. Also made it a little more robust. ...

Simple stands for the FrSky Horus, a device not known for its artistic value :)\nFor simulator use, it can be used with a 90° USB-cable plugged in.\nPrint Settings\nPrinter: CTC\nRafts: No\nSupports: Yes\nResolution: 0.2mm\nInfill: 20%

New Grips for the Horus X12s by FrSky. I wasn't Impressed with the Initial Offerings. These New Sticks Exceed My Expectations, Boasting a Longer, Thicker Design That Fits My Needs Perfectly. ...To Install Them Correctly, Simply Thread an M4 Screw into...

... new handlebar is properly secured before testing it out. * Perform a few test flights to ensure everything is working smoothly. By following these simple steps, you can easily replace the handlebar on your Frsky Horus X12S remote control system.

Small desktop pedestal elevates the Horus for coding as soon as the USB port is securely connected

Neck Balancer For Horus X 10

The Horus controller is enormous, making it extremely unstable when using a neck or shoulder strap. I urgently needed a balancing arm that would be incredibly robust and fit snugly in the tight space surrounding the small hook loop. This design was...

FrSky's innovative Horus 10 balanced holder.

Protect Your Investment with FrSky's Top-Notch Horus X12S Stick Protectors.

These custom-made switch cushions are designed specifically for the FrSky X10(S) radio system, but may also be useful for other radios as well. They were created with the top long switches in mind, which can be particularly challenging to access on...

Gimbal protection for Frsky Horus X12S v1. Gimbal protector with hooks for elastic band v2. Gimbal protector without hooks v3. ...Seperate Left and Right Protectors.