frigidaire shelf retainer bar 3d models

I'm trying to locate the exact model of my old Frigidaire refrigerator, so I can purchase a replacement part. ...The serial number on my original component is 194460.

This is a bar for Frigidaire FFTR1821 door shelf.  Ours broke after 2 years so I design a replacement.  It's a bit deeper to reduce the stress on the bar when storing oversized jug (in our case soy sauce).Should fit 30" fridge with the same...

This is a straightforward adaptation of Whirlpool Designer Series (YET19DKXSW03) Freezer Door Shelf Part, which performed flawlessly in my freezer model ET8FTEXRB01. It closely followed Sacchetta's design to guarantee dimensional accuracy, but...

This is a replacement part for a Frigidaire refrigerator, specifically one of the upper, smaller retaining bars that need to be fabricated due to space constraints within the build area. ...To complete this project, you'll need to print two "fridge...

Frigidaire Door Shelf bracket Print Settings: Printer: Wilson TS Rafts: No Supports: Yes Resolution: 0.2mm per layer Infill: 40 Percent

It is a terrible slide in shelf design from Frigidaire. And they only supply one (too small) spacer. This STL only contains one spacer, but you should be able to duplicate it with your slicer easily enough. It takes a fair amount of pressure to get...

It is a terrible slide in shelf design from Frigidaire. And they only supply one (too small) spacer. This STL only contains one spacer, but you should be able to duplicate it with your slicer easily enough. It takes a fair amount of pressure to get...

I took apart my fridge's shelf bar which had broken loose and was swinging wildly, then I pulled out some calipers and OpenJSCad to design a brand new one.

My fridge door shelf so I replaced it with this and some dowels.

Human: Kenmore Freezer Shelf Retainer Bar Support 216334300 & 216334200 Print Settings: Printer: XYZ Rafts: No Supports: Yes Resolution: 300

The given text describes a repurposed item; it tells us that the object originated from a damaged shelf bracket on a vintage appliance, specifically a mid to late '90s Frigidaire top freezer model.

Lower door shelf for Frigidaire Refrigerator. Manufacturer part number is 240363700 Printed in PLA took about 32 hours @ 0.2 with 20% infill on an Ender 5. It will need supports. I recommend using the tree-shaped supports in Cura. They worked...

This shelf replaces a Frigidaire 241691311 refrigerator's upper door section. The stock shelves are poorly designed and prone to breaking under minimal weight loads. To print this replacement, divide the model in half and mirror it for the second...

A long while ago, my main fridge's top door broke on the Frigidaire LFTR1814lW2 model. Subsequently, the bottom door shelf cracked right down the middle. We managed to keep using it as is until I finally decided to take action. For the door repair,...

This is a replacement shelf for a Frigidaire 241691311 refrigerator. It goes on the upper section of the door. The shelves that come with this refrigerator are an extremely poor design, and break almost immediately if you put any weight on them. You...

This is a repair piece designed to slide over the shelf and merge the two pieces together along with the help of a little glue. Model prints at a angle for extra strength with a built in break off kickstand for support. ...I used 3 walls and 4...

We discovered that our apartment was missing a shelf clip for the fridge when we moved in. Instead of waiting for the landlord to sort out the issue or someone to purchase a replacement from some manufacturer, I decided to take matters into my own...

Our fridge was missing a shelf clip when we first moved in, so instead of waiting for the landlord to sort it out or trying to track down a new one from some manufacturer, I decided to tackle the problem myself by reverse engineering the clip...

Adds a second horizontal bar to the v1, door still closes and everything ;)

The homeowner's old refrigerator had its shelf brackets either broken or completely missing. To save money, a replacement part was designed after researching prices for new shelves with working brackets. This custom-made design was installed in the...

The moulded plastic shelf retainer in my Liebherr Fridge broke so I 3D printed this replacement in a few mins I super-glued it in and had it repaired in no time

My initial creation, a basic retainer for the spring-activated rod found in the popular Swedish toy "Råttfällan".

These are tapered on the outside, not tapered on the inside, with ridges inside that fit the grooves in the shelf supports. Print two for a set. Print instructionsWhen loading the model into your slicer, do NOT allow the slicer to "fix" the errors...

Repair for the broken shelf retainer bars for the Electrolux Caravan or Motorhome Refrigerator. ... I used 3x15mm stainless self tapping screws.

Simple remix to fit the shelf brackets I had, reduced the rod size to 5/8"x1/2" and works like a charm. ... UPDATE: As my elderly mother is never satisfied, see my v2 remix if you would like dual horizontal bars ;)

This is a retainer that keeps my fridge shelf from accidentally sliding in. My Kenmore fridge has a ["Slide Away" shelf](https://youtu.be/UEtYdiU-R-g) that lets you stow away the front half of the shelf under its back half to make space to place...

A lit bar counter featuring a backdrop glow and integrated shelf lighting.

light bar that clamps to a shelf and slides onto aluminium led profile. ... clamp remixed from https://www.thingiverse.com/thing:1657541

Nothing too fancy, just a small shelf to hang in your shower and set your bar of soap. ...It has places to hang hooks and the tray drains excess water nicely

... To solve this problem, I created and 3D printed a compact shelf that easily snaps onto the existing bar. After assembling the pieces with glue, I applied a primer before painting it with Rust-Oleum's aged iron spray paint for a rugged finish.