freewing l39 3d models

I have modeled a simple fuel dump port cover (two different lengths offered) for the Freewing F-14 Tomcat 80mm EDF Jet. Some trimming of the stock foam fuel dump cover may be necessary to fit over it. It should be a snug fit, but should be glued on...

This is an edit of Billyrayx's: https://www.thingiverse.com/thing:4720112 Freewing SU35 Landing Gear Brace with Retract Mount to clearance the space for the retract to fit in this mount better, to clearance the slot for the landing gear leg to extend...

Reinforcement for the elevator servo of the 1:11 Freewing F-4 Phantom. Since the servo can come loose after several flights, I constructed a frame that is simply glued over the installed servo with Uhu-Por or superglue. The servo does not have...

... of the original foam missile with a clear nose cap in place. The printed nose cap can serve as a vacuum form plug to pull a clear nose cap. I added a new second stage with a slot accommodating the Freewing 90mm F-16 weapon attachment hardware.

This is a 1/10 scale CBU-87 Combined Effects Munition designed for use with the Freewing A-10 model aircraft. The munition features a specially crafted pocket to accommodate the mounting plate, specifically Thing Number 2725747, developed by...

This design is intended for use on the old "PRO" version of the Freewing 70mm F-16, which features a Freewing 3048-2300 Kv brushless outrunner. I suspect it will also work with the "normal" outrunner motor found in non-high performance versions, but...

Upgraded main-gear mounts revolutionize the 90mm Freewing F/A-18E Super Hornet (Vector Thrust version), transforming a weakness into a robust foundation. The original mounts were woefully inadequate, frequently requiring removal due to damage from...

I have created a rear battery tray and wire tunnel for the Freewing F-14 80mm EDF Jet. The rear battery tray is designed to fit tightly and glue into the foam slot on the floor of the jet. After using RCGeek's idea of carefully carving out foam...

***1/14/21 Update: Angled Plug updated/improved.*** I have modeled screw hole plugs/covers for the wing box cover on the Freewing F-14 Tomcat 80mm EDF Jet. These plugs/covers are placed inside the foam holes after screwing on the wing box cover to...

Alternative main landing gear mount for Freewing F-35 V3 Lightning 2. I broke the OEM mount as shown during a rough landing. This design reinforces the location of the fracture and provides additional support to the retract servo mounting flange. It...

Shorten both grub screws by removing ~0.7mm from the contact end.Note: The Freewing Stinger 90 Nose Landing Gear Connecting Pin (SKU: FJ30511085) is purported to be an ideal replacement for the F-35 with spacers.CAUTION: Filament selection is key for...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Replaces the cheap looking foam overlay on the vectored thrust nozzle. The foam overlay is glued on with a tacky glue and with care can be pulled off intact. This is a direct replacement. Be aware that it weighs some 30g more than the foam...

I copied the original rail from my F-16 since I lost one in flight. ... It's an old design done with 123D.

If you want to use a gyro on the su-35, there is not enough space, But here is a way to help you solve the problem.

Here are two gauges to make the basic control surface setup somewhat easier. ... A gauge for setting up the split rudders, 22.5 mm per side plus one to set up the Up trim of the inboard elevon.

This fits over the retract in the main gear well. Provides support for the plastic retract housing as well as the main gear strut. Right side STL is included, mirror in your slicer to create the corresponding left brace (the brace is not...

This is one of the first parts I've made so far and its based on a few other designs for front landing gear braces on R/C planes when used around grass runways.

For a stronger nose gear, you can install this plate and use M3x55 screws instead of the original

A more accurate and heavier nozzle for the F-35 V3. The existing foam nozzle plugs into the rear fuselage and is held in place with tacky glue. It is easily removed and this fits in its place. I suggest taping over the join inside the tailpipe...

The human form can effectively grasp and manipulate the downward pressure required to operate an esc on a 90mm T45.

Simple harness to keep wires and cables clear of the canopy joins

Re-designed with seperate pylon and spiralized outer contours to reduce weight.

Used to craft efficient and speedy rivet lines on precision-painted miniature aircraft models, scaled at 1/5th size, with additional sizes available upon request. ...Email me directly for a quote on custom 3D printed solutions: Rockerman61@yahoo.com...

The Gripen needs weight in the tail to achieve an acceptable CG position. This nozzle has accommodation for up to 60g of small lead weights, in addition to weighing over 60 grams itself. Print wide-side down, with supports. You will need to peel...

A model of the A-1 unguided rocket for the Me-262 A total of 26 need to be printed. ... The wooden supports need to be done separately (i might design it later)

I design and manufacture scaled-down rivet lines specifically for use on painted foam aircraft models, typically at a 1/10th scale but also available in other sizes upon request. ...For information on pricing and to inquire about 3D printing options,...

With my Yak 130, I've taken apart the wing tips to access the implied weapons pylons. Using a 5mm brass tube, I drilled a passage for the cables that connect the aileron servo, allowing me to route them through easily. The LED lights at the end of...

I've created a configuration for the T-45, incorporating a custom pylon and munition system. The bomb cradle consists of eight interconnected components, securely fastened together via adhesive bonding. ...In turn, the pylon is rigidly attached to the...