freewing f 14 build 3d models

AIM-54 Phoenix missile for Freewing F-14 Tomcat.

For freewing twin 80mm F-14 convert to turbine power.

The AIM-54 Phoenix missile is specifically designed to work with the Freewing F-14 Tomcat model.

AIM7 for Freewing F-14. Fits on the pylon at https://www.thingiverse.com/thing:5138357 Mounting lug is optional, as the missile can be glued in place on the pylon. (One fin on the forward section is missing as it would be concealed by the...

The files here are the components I used to convert the Freewing F-14 80mm EDF model to a single center mount turbine model using the xicoy x45 turbine. The Rx components deck was printed in 2 colours with the fillament change done at layer 16. ... ...

Replacing a Lost or Broken Pitot Tube on the Freewing F-14 Tomcat is a Snap. No need to purchase an entire nose cone when you can make your own pitot tube replacement at home with just a few simple steps. Print out the design in high resolution,...

I was fed up with the flimsy nose gear brace constantly snapping on my Freewing F-14, so I opted to 3D print a sturdier one that would withstand the rigors of flight. This custom part should perform better than the stock component since it eliminates...

The nosegear retract mount attachment for the F-14 is rather weak. The plate goes in the compartment under the canopy and 55mm M3 screws pass all the way through from the retract to better spread landing loads to the airframe. ... The block...

... attached using the optional socket (part "C"). These fit standard Freewing ordnance mounting lugs. ... A Sidewinder to the correct scale is at https://www.thingiverse.com/thing:5136361 You will need to print a left and right side version.

Sidewinder scaled for Freewing F-14 Mid section has breakaway pads to help stabilize it during printing. Print the mounting lug solid as it needs to be strong. The rest can have minimal infill. The lug is standard Freewing dimensions. ... A socket...

I have designed 3D printable replacement ventral fin for the Freewing F-14 80mm EDF Jet. This is very easy to print (lying flat on the print bed). Please be aware that the 3D printed ventral fins may be heavier than the stock Freewing wooden...

To adjust the end-tube of the freewing F-14 to optimize it for the FMS EDF a small tool. ... Glue sandpaper on the cone and the cylinder and sand it, till it fits, than seal the surface with tape or parquet-laquer

I designed this external wing tank for the Freewing F-14 Tomcat. I have yet to print this part, but I will update this as soon I do. There are five parts. The Nose, Center, Rear which makes up the main tank. Then the pylon on and wing mount. ...The...

I crafted an external wing tank for the Freewing F-14 Tomcat from scratch. As soon as I get my hands on a 3D printer, I'll be updating this project with live photos of it in action. ...This ambitious design consists of five intricate parts: the Nose,...

I didn't care for the cheese grater appearance of the Freewing F-14's lower fuselage, so I decided to take matters into my own hands. I printed two custom intakes and cut a new thin plastic sheet to replace the perforated one. It now looks much...

I added a servo to create a moving tailhook on the Freewing F-14 80mm EDF jet, and needed a means of shielding it from wires accidentally inhibiting the tailhook servo operation, so I created a simple shield to help keep the tailhook servo separated...

I have designed a simple fuel dump port cover for the Freewing F-14 Tomcat 80mm EDF Jet. Some trimming of the stock foam fuel dump cover may be necessary to fit over it. It should be a snug fit, but should be glued on to ensure security. ... As...

I have designed screw hole plugs for the wing box cover on the Freewing F-14 Tomcat 80mm EDF Jet. These plugs are placed inside the foam holes after screwing on the wing box cover to conceal the screw holes for better visual presentation. The...

I have designed a main wheel-well Side Covers for the Freewing F-14 80mm EDF Jet. This is not meant to hide/conceal the main wheels, but rather make the main wheels look less noticeable when the gear is retracted, as well as fill the noticeable gap...

First attempt at creating a modification to add trailing link main gears to the Freewing F-14. This was generated as a test fit prior to machining. ...It replaces the lower "fork" in the A-10 trailing link nose gear.

First attempt at creating a modification to add trailing link main gears to the Freewing F-14. This was generated as a test fit prior to machining. ...It replaces the lower "fork" in the A-10 trailing link nose gear.

One version does not have wheel axel access once installed, and the other provides full wheel axle access.*** I have modeled F-14A/B (found on some D-model F-14's as well) model main wheel covers that glue (do not get glue on the wheel axles) onto...

I have modeled main wheel well side covers for the Freewing F-14 Tomcat 80mm EDF Jet. These side covers visually conceal part of the wheel for improved visual presentation. Ensure the fitment, clearance of the wheel and the side covers, etc. is...

I wanted to raise the ESC's of the Freewing F-14 80mm EDF Jet to allow some of the wiring to run underneath, so I created an ESC tray that glues onto to the foam walls, and the ESC's are then secured to the tray (via Velcro or other secure means). ... ...

I have designed removable ventral fins for the Freewing F-14 80mm EDF Jet. This can come in useful when wanting to put the plane on a plane stand more easily, as well as transport it without the worry of the ventral fins getting in the way. The...

I have modeled a simple fuel dump port cover (two different lengths offered) for the Freewing F-14 Tomcat 80mm EDF Jet. Some trimming of the stock foam fuel dump cover may be necessary to fit over it. It should be a snug fit, but should be glued on...

***1/14/21 Update: Angled Plug updated/improved.*** I have modeled screw hole plugs/covers for the wing box cover on the Freewing F-14 Tomcat 80mm EDF Jet. These plugs/covers are placed inside the foam holes after screwing on the wing box cover to...

I have created a rear battery tray and wire tunnel for the Freewing F-14 80mm EDF Jet. The rear battery tray is designed to fit tightly and glue into the foam slot on the floor of the jet. After using RCGeek's idea of carefully carving out foam...

For a stronger nose gear, you can install this plate and use M3x55 screws instead of the original

This is a semi-scale pylon to mount on the underside of the wing "cuff", where it is screwed onto the three molded-in bosses. You will need a left and right handed version. It will hold a Sparrow or AMRAAM on the vertical section and a Sidewinder...