freewing al37 3d models

Fuel tank for the Freewing A-4E/F Skyhawk. Best printed in PETG walls for the initial and afterward epoxy-ed internally with thin finishing resin or diluted resin to ensure any gaps from printing are closed. Print settings I used: - 0.6mm...

These plates are designed to firmly secure the ailerons on the Freewing AvantiS, and a few planes have suffered terrible crashes because the aileron horn was not properly glued in place. With this plate, you can securely fasten them; you can glue...

tray that screws into the battery compartment of the Freewing Avanti S 80mm EDF Jet. The tray allows for the RX/Gyro to be positioned above and out of the way of the control board. This also provides a less cluttered look to the compartment. Be...

I have designed a main wheel-well Side Covers for the Freewing F-14 80mm EDF Jet. This is not meant to hide/conceal the main wheels, but rather make the main wheels look less noticeable when the gear is retracted, as well as fill the noticeable gap...

https://www.rcgroups.com/forums/showthread.php?3705995-Freewing-SU-35-to-SU-37-Conversion-Mod It took many hours of iteration and design work to make this conversion mod. If you like my designs and found this helpful, a tip would be appreciated. I'd...

This UB-16 Rocket Launcher can be attached to the stock Freewing L-39 Pylons in place of the drop tanks that come with the kit. Remixed to print in 2 parts with a joiner and slightly enlarged to fit the pylon better. Epoxy some magnets into the...

I love also my Freewing Albatros L39, so I added DJI FPV on it (https://www.youtube.com/watch?v=GuF2SiQ7Ta8). Few months ago I came across with the Insta360 go. It has a amazing stabilisation so I decided to have a go and try to fit it in my Albatros...

I have designed screw hole plugs for the wing box cover on the Freewing F-14 Tomcat 80mm EDF Jet. These plugs are placed inside the foam holes after screwing on the wing box cover to conceal the screw holes for better visual presentation. The...

The Freewing F-5 has the same size, so some parts may work there too. My tricked out Starmax F-5: https://youtu.be/BH9PzaeX_T8 Retractbase01.STL - The mounting base for the retracts. Rectractbase02.STL - Mounting base for the main retracts with...

The Freewing F-5 is the same size so some parts should work there too. My tricked out Starmax F-5 can be seen here: https://youtu.be/BH9PzaeX_T8 Retractbase01.STL - This is the mounting base for the retracts. Retractbase02.STL - The main retracts...

Print the inner and outter Nozzlepart 15 times the ring one time and glue it with superglue togheter :)

Hello for the T-45 I have created a 3DPUP set to add scale details to my T-45 Goshawk. The parts were printed with a Dremel 3D40 using PLA, and Simplify3d was used as slicer software at a 0.2 layer height with raft enabled. For completion, drills in...

The wooden rudder tip snapped off, so I fabricated a sturdy replacement out of durable plastic.

I made a replacement clip for attaching the stock nose gear light to the nose gear strut. I have the stock one and a mirrored version included. If you like my designs, a tip would be appreciated. ...Tips can be sent to: http://paypal.me/sukotto88

Replacement grill for the F-86

Centerline tank for the MIg29. Forward section of the tank holds 41oz of diesel or kero. Once printed, coat inside and out with epoxy resin. ...

What it does: Improves handling and lowers stall speed. Will they decrease top speed? Not that I have noticed. Vortex generators do add drag, but it's offset by reduced turbulence drag, so total drag is about the same. Whats included: Wing...

Tired of breaking and replacing the Phantom's pants ;D I designed my own.

The foam wingtips suffer a lot of scuffing and they become too flexible. The 3D printed are a good replacement and protect the wings. ...Remember to print one mirror image.

A replacement for the stock plywood fin

Main gear and cradle for retract and gear brace

Replacement Door for the Nosewheel Well. The hinges and horn are separately printed so the door can lie flat on the inside surface while printing, thereby avoiding supports altogether. Print the small parts solid for added strength, but use 10%...

To add scale realism to the Me-262. ... Printing, installation and use is under your own responsibility.

I've created a T-45 POD with pylon attachment using my 3D printer. I printed the parts on my Dremel 3D40 machine with PLA filament. To slice the models, I use Simplify3d software, setting the layer height to 0.2mm. The POD is divided into three...

I took an existing model by bettsmums and made some subtle adjustments.\r\nhttps://www.thingiverse.com/thing:2820091\r\n\r\nTo simplify the printing process, I embedded the "X" marker directly within the tube itself, eliminating the need for a...

A Simple yet Effective Solution for Secure Battery Retention in the Stinger 64. I designed this battery retainer plate to be 64mm wide, taking into account the modifications I had made earlier to accommodate my Nanotech batteries. These adjustments...

Here's a Pylon I Designed That Allows Me to Mount Bombs to My Jets. To Assemble, Print Out All Parts. The "Box" Style Free Wing Attachment Hardware Mounts onto the Wing by Cutting Out a Bit of Foam to Ensure a Flush Fit. Next, Glue the "T" Hardware...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Drew this up after my kit arrived with only one nozzle. Straight fit onto aircraft and weighs the same as OEM nozzle. ...

Print as light as possible except for the mounting lug (if used). To stabilize printing vertically, some breakaway pads are added to the forward section. Remove after printing. ... Underwing pylons for the Gripen are here: ...