free g max models

This is a model and instructions for how to build your own fiber optic light engine that is smart and can be controlled through google home. This version uses a smart LED light bulb as the source of light. It can use any smart light bulb that is...

Extending the print head cable on this model is not unheard of, it is a common change made when upgrading this printer to a direct extruder. The portal cable (black) does not need to be extended, even for the extension kit for 50mm, as long as you...

On homemade springs using generic musical wire When it comes to homemade magazines, the models by Thanhtacles are designed to use drum springs unlike the box springs exemplified by their commercial counterparts, for what I assume is the most...

We are presenting a new wind turbine device, that is easy to 3d print, it can be made handcraft once it is viewed it components and how they get assembled in a very easy and intuitive view, This system have several pending patents and the device...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 stencil_drawing =...

And yet by the time Babbage died in 1871 without a working model. During those years, Per Georg Scheutz built a number of difference engines based on Babbage’s published works - also funded by the government and would evolve to become the first...

...I propose some activities to do programming this robot: First goal: Making it move The first and basic activity could be to program and model their movement, to find the correct position sequence for each leg for a forward run. First step: assembly.

 This model is currently a working draft. Solar astronomy has inherent dangers, please be sure you understand these (see also below). Use is at own risk. More general information about this approach to solar astronomy can be found at the Sol'Ex...

I got a package of 5 and when I opened them I found that the design had changed slightly and the material they used on the newer models was slightly thinner. The original clips were therefore a little sloppy. I adjusted the clips to fit the newer...

 The switch is wired so it goes from Off to On with no sounds to On with sounds. ...

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

The assembly is not complicated, for each configuration I put exploded photos, pay attention to the insertion of the brass threads, (there are 2 models you need both), and to the direction of insertion, those placed in the attachment of the guides,...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

I made a CAD model, did some tests to see what would work and built this desk. It's called ‘Carl’s Desk', because the original was made for Carl.</strong></p><p><strong>This is a rebuild for the print tables contest, the 3D printed parts are now...

... and no one is going to fix it. ...Download files one at a time by clicking Download each time. ### My some other things: Category: Keychains

The Raspberry Pi controller has a radio module attached to it for issuing commands, though I used the slightly different NRF24L01+PA+LNA model which offers better range. You could also use the same NRF24L01+ module as the puck uses, the wiring and...

Generate and print your own, compatible with any existing threads!This model was designed in Fusion 360 and uses 3 required input parameters and standard Metric thread profile equations to generate a cap that will perfectly fit any of your threaded...

Changelog: Update 2021-03-01: Steve (faultedlogic) made a remix for current A8 models with plastic bearing blocks. Update 4 (2018-06-17): added countersunk hole for chain fence Update 3 (2018-06-11): updated left motor mounts for different type of...

We don't use the shell.PrintingPrint all models in their original orientations.The parts should be printed with support. Try tree support as it wastes less plastic and is easier to remove in one go.</p><p>I printed my parts in a black/red color...

Designed with the help of acoustic modelling software. Comes with carbon fiber slide, complete with PLA stockings.</p> <p>Also available in large bore version at <a...

Check out the Raspberry Pi 3B+ here: https://www.raspberrypi.org/products/raspberry-pi-3-model-b-plus/ The controls are simple but there's enough buttons for most games. D pad for direction control and 4 front buttons provide your basic SNES type...

I designed this model for my daughter, who wanted a treasure chest to go with her pirate costume.  She wanted it to be “really big”, so this design utilizes the nearly the full volume of the MK3s to make three sections that bolt together.  It has an...

&nbsp;It is recommended to use MERV13 or higher for virus carrying particles.&nbsp;The fan is a Black &amp; Decker 9in Mini Box Fan, Model BFB09W*.CostAt the time of writing this the total cost is the same for each of the 3 versions as the different...

This model includes both a solid and a honeycomb version whether you want to print a more authentic and traditional version of the warlock or if you want it to be more unique.&nbsp;I used absolutely bottom of the barrel parts to get this to a fully...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

The "cylinder" rotates, and will index to set the drill guide sizes for any of the 6 holes. This version has a "cylinder" which is designed with holes that are 2mm, 3.6mm, 4.4mm, 5.2mm, 6.0mm and 6.8mm (which correspond to 5/64, 9/64, 11/64, 13/64,...

If you want to use the hardware I intended this to use:Hinges Bolts- https://www.mcmaster.com/91292A018/ (you will need to thread inner most hinge)Hinge spacer- https://www.mcmaster.com/91755A311/ (you can see in the photos a little bit of white in...

IF YOU ARE HAPPY WITH THAT, A LITTLE DONATION WILL BE VERY NICE <3https://www.paypal.com/donate/?hosted_button_id=5F525DYM8GXK4 If you want to do a remix or changes to the design, you can get the Fusion 360 and STEP file here:...

Since the build volume on the Prusas is relatively limited i decided to maximize the footprint of the stand for stability. As for the height, the 2 piece construction while theoretically takes more time to print, there is no need for support for the...

We are modelling the *BELT* tooth here, not the tooth on the pulley. Increasing the number will *decrease* the pulley tooth size. Increasing the tooth width will also scale proportionately the tooth depth, to maintain the shape of the tooth, and...