free fbx models with textures

 A modern take on the common Lampshade inspired by the design of my Prusa i3 Mk3S.The Lamp was designed to use the Ikea Hemma cord set.Everything was printed in PETG.PLA should also work just fine as long as you use LED lights that don't get too...

Customized version of http://www.thingiverse.com/thing:287025 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:279864 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=279864 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:116042 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=116042 Instructions Using the following options: mirror...

In my experience the two 500mAh batteries (combined 1Ah 3.3V) last for three months provided that they don't get drained when there's no WiFi or Internet and the ESP32 is constantly attempting to get data. in order to protect your cells from...

Things you'll need: a 3D printer with a print bed around 300x300mm 7 1kg Spools of Grey PLA (might only need 6 spools I had a few failed prints & design changes) 1 1kg Spool of Translucent Red PLA 1 1kg Spool of Clear PLA (optional if you want to...

There's way too many sizes for me to make one for each without someone needing it but I'm more than happy to add one if someone wants it!  Here's the OnShape document if you'd like to copy it into your workspace and mess with it.Buy me a...

A little force might be required, and when viewed from the outside should fit snuggly at the bottom groove.M3x10 screws can be used to ensure it stays in place, but I found it wasn't needed.The Stepper Driver and RTC module each has a plate that you...

In step 23, replace part E1 with the Alpha - Outer parts; all other parts in step 23 are the same. Alpha - Insert: The Alpha Insert parts are designed to bolt onto part E2 after it has been cut in half. The cut should go the short way through the...

Customized version of http://www.thingiverse.com/thing:287025 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options:...

Thread the hole with the tap, clean the hole, then screw an M3 screw into it. Repeat 3 times at least (One on either end and one in the centre. I did 4 holes, but it's up to you) 10. Install the belt Holder on the back of the metal backplate 11. ...

It is also cool to have dimmer remote on the lamp, use colorful LED strip or connect it with voice...

Assembly Method: So we looked at what was out there and wanted to simplify current designs as much as possible, we also wanted to design for laser cutting so these can be mass produced. -Its laser cut so 100-1000 can be produced a day -We...

Customized version of http://www.thingiverse.com/thing:401429 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=401429 Instructions Using the following options: ...

Customized version of http://www.thingiverse.com/thing:287025 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=287025 Instructions Using the following options:...

... part.</p> <p><b>Warning</b><br/> <i>This device operates on 220V mains. You must be aware of the safety requirements working with 220V networks. Remove the fuses before working on 220V networks. ...Make sure, there is no power in the cables.</i></p>

Here, beneath the golden light of Elendil's radiant star, the wise and just rulers of Gondor have taken up their sacred trust, guiding their people with wisdom, courage, and unwavering dedication to the cause of justice. The noble lineage of...

Customized version of [http://www.thingiverse.com/thing:310541](http://www.thingiverse.com/thing:310541) created with Customizer! ... Instructions: - Border width: 1 - Panel shape: 0 - Picture dimensions: [0.024, 0.031, 0.027, 0.039, 0.024, 0.043,...

Then the main battery distributes to all parts of the rover.Exo-Battery Docking tubes: used to dock Exo-Battery to main battery.Rear cam : used to identify the view in back side with scanner and sensor.Exo-electrical cabin : similar to Electric cabin...

The exact nature of this infestation is not specified, but it could imply that the lions are causing damage to the bales or interfering with their intended purpose. More context would be needed to fully understand the situation.</s> Lions invade...

To discuss this topic, I will respond with: There is no deeper significance in picking a number, such as nine; however, one could analyze the cultural and symbolic representation of that specific digit within modern society and possibly identify...

Secure hold on sheet metal Ensure firm grasp when working with sheet metal Maintain a strong grip while handling sheet metal Keep a tight hold on the sheet metal to prevent slipping Firmly grab the sheet metal for safe manipulation Adequately clasp...

It's like having a puzzle with a missing piece. poon assistant In brief, the text indicates the absence of a crucial element: a bolt. It's like trying to finish a project without one essential tool.</s> poon<|im_start|> assistant To summarize, the...

The process needs one M3x18 screw, one H M3 nut nylstop and a 2,5 Allen wrench.The picture below shows the required parts to assembly the phone stand.Step 1 : Inserting the nut inside the support tablette pt1Put the nut inside the support tablette...

Once the carriage bolt(5) is fed through the slotted lever(1), it should stand on its own with no need for support, and adjustment should be as simple as moving it with your hand and it should stay in place on its own after adjustment.  A slip...

Calculate the difference of the longitude where you are with the closest 15° multiple reference longitude (0°, 15°, 30°, 45°, 60°, 75°, 90°, 105°, 120°, 135°, 150°, 165°, 180°) 3. Turn the time ring by the corresponding number of degrees (1 notch =...

Reszta drobnych elementów, przewody, złącza itd....XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXA complete Led lamp for a marine or freshwater aquarium, this is the whole project of the LED lamp in the second version V2 with a power of 350W with...

""" assert self._patch_type == 'circle' center = (self.convert_xunits(self._center[0]), self.convert_yunits(self._center[1])) width = self.convert_xunits(self._width) height = self.convert_yunits(self._height) self._patch_transform =...

A customized version of http://www.thingiverse.com/thing:46884 created with Customizer! Instructions: - Perimeter: -1000 - Per Hole Width: 3 - Per Hole Height: 10 - Tag Thickness: 3 - QR Code Tolerance: 0.001 - QR Code Scale: 1.6 - QR Code Rotation:...

Customized version of http://www.thingiverse.com/thing:279864 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=279864 Instructions Using the following options: seed =...