fredman mic clip

Kamado Joe Junior iKamand Adapter
prusaprinters

(Note that the photo below was from a model I made with an 80mm aluminium tube, I forgot to take photos for the 30mm model.) Once the sealant is cured, the adapter can be slotted into the Kamado Joe Junior and the screws re-installed on the...

Modified MIK adapter plate suitable for Ortlieb rear pannier bags
prusaprinters

Motivation (english)I use the MIK system on my bike, which allows you to clip anything onto the rack. <br>But it is annoying that you cannot use the MIK adapter plate with Ortlieb pannier bags at the same time. The design of the MIK adapter plate...

EX-MAX Arcade Fight Stick
thingiverse

( I used these off Amazon - SoftTouch Self-Stick Non-Slip Surface Grip Pads) Top Panel Options: Top Left EX-MAX Japanese.stl – 40mmx85mm mount holes will fit Sanwa & Seimitsu sticks or any others that use the same mounting Top Left EX-MAX...

TARDIS LED Lamp
prusaprinters

You'll need 8 of these. Assembly InstructionsOnce everything is printed follow the steps below.Please note, much of this will just push-fit and clip into place, but some parts such as the door handles, keyhole, and possibly the windows, may require...

Cassie Bracelet
thingiverse

http://www.thingiverse.com/apps/customizer/run?thing_id=401429 Instructions Using the following options: pattern_size = 10 pattern_clip = 95 pattern_copies = 20 pattern =...

X/Y/Z upgrade kit for acrylic Prusa i3 clones (based on TR8 leadscrews) - No more zip ties!
prusaprinters

a flat piece of hardwood, or to a table, as I did).. A simple switch mount that clips onto the Y frame's front threaded rods, into which you can mount a common rocker switch that you might want to use for main power. It has two additional holes that...

(V1) For BIQU B1 - DIY Enclosure - Remix of Prusa's IKEA Lack Enclosure - with extra doors (opening on 3 sides)
thingiverse

Those sheets are: **Bottom-Corners.stl** **Door-Knob-(x3)-and-Cable-Clips-(x10).stl** **Top-Corners.stl** **Top-Extenders.stl** Additional parts that are not ganged up on a sheet with others:...

Ornithopter Dune 3D Printing Model | Assembly + Action
gambody

The 3D printing model’s chosen scale is 1:64 for the FFF/FDM version and 1:128 for the DLP/SLA version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 61 parts;- A printed model stands 368 mm tall, 456 mm wide, 560 mm deep (platform +...

Onewheel XR VnR Battery Pack (63v 16Ah Li-ion 20700 15S4P)
myminifactory

Then clip the BMS plate over one side of the battery cells so that the black wire reaches the negative 2x2 corner with ease.7. Cut some lengths of Nickel strip, 75mm and 30mm lengths, you'll need a few but cut them as you continue through the...

Full Build Instructions for Slack Lack (Ender 3 / Ender 3 Pro) Plus Accessories
prusaprinters

In my case, I'm running up and down the sides of each leg, as well as along the top, except in the case of the front in which I only do theback of the leg. Attach each clip with finishing nails or wood screws; attach the LED strips as you go for...

Hercules - QIDI X-Max Carriage for BMG & Dragon / E3D V6
prusaprinters

Clogs are a thing from the past and no more grinded up filament stuck in the gear.Here's a comparison picture by Hercules user techguychad:What to print:Print these...

Hercules - QIDI X-Plus / I-Mate (S) Carriage for BMG & Dragon / E3D V6
prusaprinters

Clogs are a thing from the past and no more grinded up filament stuck in the gear.Here's a comparison picture by Hercules user techguychad:What to print:Print these...

Mounting plate for 5.25" speakers in Stern pinball machines
prusaprinters

Too much and the connector will get too fat to fit into the housing. When inserting each connector, pay close attention both to its position and its orientation.On my machine, the speaker negative goes on the side of the connector with the clip, but...

Temperature Controlled LACK Enclosure With Motion Sensor LED Lights
prusaprinters

Input Current: 0,11 AVoltage: 12 VN/A • Molex 4-pin to 3-pin Fan Power Adapter Converter Cable1 x Molex cable to cut and connect fans to MH1210A temperature controllers.4-pin LP4 to 3-pin TX3 Fan Power Adapter Converter Cable.Simultaneous connection...

CR-10s Pro V1, CR-10s Pro V2 and CR-10 Max Maintenance, trouble shooting and upgrade guide
prusaprinters

Just read the installation and disassembly instructions of the 3D model.Filament guides https://www.printables.com/social/261164-caesar_1111/collections/159007 just pick the design you like from the collection, but it is important that you have...

Hercules - QIDI X-Max Carriage for BMG & Dragon / E3D V6
thingiverse

Here's a comparison picture by Hercules user techguychad: What to print: Print these files: hercules-1.7.2.stl hercules-dial-holder-1.3.stl hercules-belt-peg-1.2.stl hercules-fan-duct-1.3.stl bmg-handle-short-1.0.stl...

Hercules - QIDI X-Plus / I-Mate (S) Carriage for BMG & Dragon / E3D V6
thingiverse

Here's a comparison picture by Hercules user techguychad: What to print: Print these files: hercules-1.7.2.stl hercules-dial-holder-1.3.stl hercules-belt-peg-1.2.stl hercules-fan-duct-1.3.stl bmg-handle-short-1.0.stl...

(V1) For BIQU B1 - DIY Enclosure - Remix of Prusa's IKEA Lack Enclosure - with extra doors (opening on 3 sides)
prusaprinters

Those sheets are: Bottom-Corners.stl Door-Knob-(x3)-and-Cable-Clips-(x10).stl Top-Corners.stl Top-Extenders.stl Additional parts that are not ganged up on a sheet with others: BIQU-B1-ac-heater-wire-redirect-strain-relief-bracket.stl (The main reason...