frame stand 3d models

I bought a frame where the uprights and horizontals had a square cross section and made a stand of two feet connected with a wooden dowel. But the dowel is not necessary. ... This is a customizer so you can measure your frame and adjust the dimensions...

Photo frame

I downloaded and printed [fotofreak58's 4x6 photo frame](https://www.thingiverse.com/thing:5247439) but I wanted it to stand instead of hang The first file is the one I printed but the part needed a little tape around the disk to snug the leg in the...

This is a simple stand to display a plaque or picture frame that cannot stand on its own. ... As shown, it is printed in PETG with 20% infill and 3 perimeters, but it would likely print just fine with default print settings and PLA.

Easy to assemble stand for a 4”x6” photo frame.Having a few homemade ¾” hardwood photo frames for 4”x6” photos, it was only natural to come up with a sturdy stand for them. Hopefully these will work for you. The stand’s back is around 6” tall and can...

This replacement stand is designed to replace a picture frame's flimsy cardboard part that failed at the hinge, which wasn't surprising given its poor quality. To ensure good glue adhesion, I roughed up the smaller part where it connects to the...

This snappy little plan allowed us to put the Angel Moroni on this stand and mount it to the picture frame's upper right corner. We fastened it to their picture frame with double-sided tape on both inside walls. ... Thanks @JP1 for such an incredible...

This is a replacement stand for your cherished picture frames, designed to be easy to scale and attach, requiring minimal print time and few tools. It can be attached securely with strong adhesive or small screws directly into the old hinge. ... Print...

... ...Effortless printing allows for easy scaling to fit any size photo. The showcased frame measures 8.85 inches by 8.85 inches by 0.6 inches. ...This particular model was printed with PLA at layer thicknesses of 0.1 or 0.15 mm and wall widths of 1.2 mm.

Otherwise, this stand has a contemporary look and is quite light, but its shape makes it difficult to ship due to potential breakage and excessive space requirements. ...My print had unusual zigzags inside the smaller triangle, which I'm not sure were...

The one supplied was basically a cardboard part that failed at the hinge (no surprise there).I roughed up the smaller part where it connected to the back of the frame to ensure good glue adhesion.This is based on the existing stand that is designed...

* Maximum Size: Don't worry about exceeding 150 mm - this frame is designed to fit perfectly within that size range. * Thickness: A thickness of 3 mm will provide the perfect balance between stability and aesthetics. * Border: Choose from either 1 or...

The stand I made for 10x10cm ceramic tiles with engraving.

Artists require lightweight and easy-to-assemble display frames that can be quickly set up and taken down for exhibitions and events.

Combine the two pieces and you'll be done with it.\n\nThe largest frame size that's supported is:\n\n22cm high, 17.5 cm wide, and 1.8 cm long.\n\nYou might need to scale this from 100% up to 1000% in your slicer before printing.

... go! ...The maximum supported frame size is a solid foundation for any project. It measures out to be: Height 22cm, Width 17.5 cm, Length 1.8 cm. ...Don't forget to scale your design from 100% all the way up to 1000% in your slicer before hitting print.

Super basic lithophane display stand I slapped together in a couple hours. Default dimensions are for a 10cm x 5.6 cm x 3mm lithophane but please adjust/modify as necessary to fit your piece. ...:3

... perfectly. The showcased frame measures 8.86 inches X 8.86 inches by 0.59 inches in size. ...This particular model was printed using PLA at a layer thickness of either 0.004 or 0.006 inches, with walls constructed at a width of 0.047 inches.

What you need: 1- Create your Lithophane picture here: https://3dp.rocks/lithophane/ 2- Model settings to be set to fit my stand are the following ones : a. Maximum Size : 150mm b. Thickness : 3mm c. Border : 4mm d. Thinnest Layer : 0.8mm e. Base...

The grip sits on the same surface the stand in on.I use this a lot, especially when removing & installing the recoil springs. I've made a short video with some tips on how to make that go smoothly and reduce the risk of launching the springs across...

A relatively quick print that will save you from having to lean your pictures against the wall or other ornaments. The stand measures 141wx125hx90d The channel is 6.5mm wide. The pocket behind and under the picture is to accommodate the clip....

The bottom part of the stand may seem long but this depends on what size of hoop you are using as you don't want it to unintentionally tip over if you use a large embroidery hoop. If you want the adjustable height like how I have it in the...

What you need :Create your Lithophane picture here : https://3dp.rocks/lithophane/ Model settings to be set to fit my stand are the following...

Just an easy frame stand for a 15x10 picture frame

A simple, modern picture frame stand, with a low profile so that it is hardly noticeable. ...Fits most picture frames and works for portrait or landscape orientation.Can also be used to stand up signs and other artwork.

This is a versatile picture frame holder designed to stand frames that were originally intended for hanging on the wall. It can also be used as a sturdy tablet stand. ... The print settings are as follows: Rafts - No, Supports - No, Resolution - 0.2mm,...

... combination with the basic frame. Version 1.2 tested the pairing of the basic frame and stand number two. Version 2.0 brought forth an upgraded stand with improved features. ...Version 2.1 showcased a premium frame, offering advanced capabilities.

... neither frame can be smoothed out. Within the files, individual parts can also be located. Each frame measures 12cm in length, with a width of either 10.5cm or 11.5cm, and stands at a height of just 3mm thick. ... Printability remains untested.

This is stand frame which you can used to hold any equipment outdoor such as air conditionner unit. Two type of profiles are used in this design 20 x 20 mm and 20 x 30 mm. The frame is foldable and adjustable in height. Other parts are sheet metal.

Ensure your printer accommodates at least the frame's height on its surface (contacting the side against the frame). This contemporary-looking, lightweight stand is, however, tricky to transport due to its shape, risking damage and occupying...