fr7 frame 3d models

GPS/Compass holder for the FR7 frame securely holds GPS parallel to the frame, a necessity when using INAV, which demands the compass remains upright and level, as my own experimentation has consistently shown. ... A precisely drilled 6mm hole...

The Platypus GPS Mount, designed specifically for the FR7 quadcopter frame, provides a secure housing for the Matek M8 GPS module. ...To ensure proper stability and minimize warping during printing, the part is optimized to be printed upright with...

You can buy pre-printed mounts for the FR7 frame here if you don't have a printer: https://camerabutter.com/en-ca/products/tpu-prints-for-fr7-frame A light mount for the GoPro Hero 11 Mini that fits on the FR7 V6 7 inch frame:...

This is a housing and mount for a GoPro Session 5 for an FR7 v6 frame with carbon uprights. There is also a front mount below the GoPro for a TBS Immortal antenna or other T-antennas. This fits the frame well and allows for full range of motion with...

https://www.airbladeuav.com/products/fr7-7-inch-long-range-frame-kit?_pos=1&_sid=c22726d74&_ss=r 5/23/2019 Update: Files have been re-uploaded in metric units, replacing previous files in English units. FR7 v4.x Frame Files Only the latest and most...

Link to v6 (6.1 not yet available through Airblade) https://www.airbladeuav.com/products/fr8-7-inch-long-range-frame-kit?_pos=2&_sid=d22726d74&_ss=r FR8 v6.x Frame Files - Only the latest and greatest cut files will be posted. Old files will be...

!!!! Original DXF Files!!!!! ... https://www.thingiverse.com/thing:3590777 -------------------------------------------------------------------------------------------- Recommended Plate Thicknesses: Front Plate with and without slots: 2.5mm Rear Plate...

ND-compatible GoPro Hero mounts for the FR7 frame by @stynkebutt. ...Just the Hero 8 for not, but more to come later.

GPS modules are designed to mount directly onto the FR7 frame. - The BN880 GPS module is a reliable option that provides accurate location data. ...- The SAM-M8Q GPS module is another high-performance choice, ideal for demanding applications.

Quadcopter enthusiast seeking a reliable GPS solution for their FR7 frame? ...Look no further than this high-quality GPS holder specifically designed to integrate seamlessly with the BN880, BN180, or BN280 GPS modules.

The FR7 frame requires a straightforward component - a spacer for the lower battery. This part fits snugly onto the battery strap and provides support where needed. Alternatively, it can be securely attached to the frame using a strong adhesive. ...The...

This is my edit of stynkebutt's FR7 frame. I've been sketching ideas for a 7-inch frame and always came back to the FR7 as the style I wanted. So instead of drawing it from scratch, I took the V4 FR7 and added a few features I wanted. What I...

Drawing inspiration from the multitude of mounts tailored to the FR7 frame, I embarked on creating a custom solution when I discovered a glaring absence of compatible mounts for the SMA, Bardpole, and BN220 antennas. ...With precision engineering, I...

Here's a high-performance Platypus Tail solution designed specifically for the FR7 frame, perfect for pilots using the DJI Air Unit with its double SMA connector and paired with the TrueRC Bardpole antenna to ensure a reliable and strong RC link.

A tpu mount for the FR7 frame which allows you to mount two sma antennas (for example if you're running a DJI air unit) and a 22x20mm GPS such as the popular BN220. Also available is a version with a slot for a bardpole antenna, though I don't have...

The FR7 frame and BN-180/280/880 style GPS modules receive a significant upgrade with the addition of a lifted GPS holder, elevating the navigation system to unprecedented heights. This enhanced GPS position is carefully designed to provide ample...

These standoff parts were crafted with anticipation, as I had to wait for the right Alu standoffs and the FR7 frame was already here :)\r\n\r\nWarning: I do not advise flying with these standoffs!\r\n\r\nPLA is recommended.\r\n\r\nThe following...

This is a tail for the FR7 frame that accommodates the Matek M8Q-5883 GPS, along with dual SMAs. I like the official platypus tails by @stynkebutt, so I designed this one to look pretty similar. ... If you’re interested, check out my completed FR7...

Since I break the print parts of my last FR7 quad, and I have some unsatisfied points, I think might just re-design the whole print set for this FR7 frame. So after some attempts, I managed to come up with a new set of parts. This time I...

Remix Refined Platypus for the incredible FR7 Frame: an exceptional upgrade featuring the following essential components: - Angled SMA - RX Hole - Matek 5883 GPS Module - TBS Unify Pro32 HV MMCX Antenna - TBS Crossfire Diversity System Expertly...

this is a simple remix of stynkebutts original GOPRO HERO SESSION 5 mount for the FR7 Longrange Frame - but 20 degree instead of 35. !!! ALL CREDITS TO STYNKEBUTT !!! ... Find original files here: https://www.thingiverse.com/thing:3601947/files

Frame: https://www.cncdrones.com/FR7-v6-Frame_p_18.html Baro:...

fr7 sTUFF

Some Parts i made for the FR7 Open Source Longrange Quad All as the names say. ... Share some Makes :)

Here are a few parts I designed for the FR7 Open Source Long-range Quad: All named to reflect their function. ... I'd love to see what others have created!

I conceptualized several components for the open-source FR7 project. I created a GPS holder that enables the SMA to be perfectly centered. I fabricated an antennae tube that attaches to the front GP mount, allowing the antennae to be folded down...

Fr7 adjustable mount.

Highter protection arms for FR7 . Used with M3 screw . ...

The FR7 Straight Arm Edition 2, enhanced with additional cutouts to significantly reduce its weight. ... Check out the Original FR7 for details on plate thicknesses and mounting hardware.

this is a high mount gps for fr7 for good pos hold with inav