fpvcycle 3d models
194 3d models found related to fpvcycle.prusaprinters
FPVCycle Babytooth (https://fpvcycle.com/products/fpvcycle-babytooth-frame-choose-your-thickness) Canopies for everyone! ...:D<br><br>Various versions with different Antenna mounts!</p>
thingiverse
Fits 450-600mah 1s batteries. ... Perfect for your FPVCYCLE Babytooth.
thingiverse
for fpvcycle babytooth print 4 pcs to use https://rotorbuilds.com/build/31167
thingiverse
Fpvcycle Toothfairy 2 Accessories ================================= + 3mm VTx Antenna Holder + 1.7mm VTx Antenna Holder + 10mm Capacitor Holder + eLRS Antenna Holder + TBS Unify Pro32 Nano Holder 15mm (PLA) + TBS Unify Pro32 Nano Holder 16mm (TPU)...
thingiverse
Sma mount for the fpvcycle molar frame. ...Fits a standard hex sma pigtail, and fits tight on a 5mm standoff.
thingiverse
I made this capacitor mount for the FPVCycle Fouride frame. It fits snug with a Panasonic 35v 1000uf capacitor. ...Print in TPU.
cults3d
Foxeer Lollipop 4 Long Tube mount for FPVCycle Cinesplore. ... Mount is designed for long version of Lollipop 4 u.fl tube to make it higher that gopro mount.
cults3d
Fpvcycle Toothfairy 2 Accessories 3mm VTx Antenna Holder 1.7mm VTx Antenna Holder 10mm Capacitor Holder eLRS Antenna Holder TBS Unify Pro32 Nano Holder 15mm (PLA) TBS Unify Pro32 Nano Holder 16mm (TPU) for the Fpvcycle Toothfairy 2 frame. ... Print with...
thingiverse
Im still tinkering with all this, I went off the dimensions on the FPVCycle page, but the bolt hole diameter for the mounts seems a touch small. If I figure that out Ill upload a v1.6 duct. ... Im working on another version ill print in clear PETG...
cults3d
Im still tinkering with all this, I went off the dimensions on the FPVCycle page, but the bolt hole diameter for the mounts seems a touch small. If I figure that out Ill upload a v1.6 duct. ... Im working on another version ill print in clear PETG that...
thingiverse
Designed some parts to work with my FPVCycle Glide frame designed by KababFPV. If you are planning on mounting the Air Unit in the center. You'll probably need to switch from 23mm to 25mm standoffs. To give you some wiggle room. ... You'll need 90...
thingiverse
Parts for the FPVCycle Cinesplore. I recommend printing the ducts from PETG and using M2 brass inserts in the mounting holes. The rear GoPro mount spacers are best printed in a rigid material as well. ... Everything else can be printed from TPU.
thingiverse
These are Insta360GO V2 mounts for the FPVcycle Fouride. One is in the vertical orientation, and the other is in the horizontal orientation. The Cap mount is for mounting a 35v 1000uF cap right next to the leads on an AIO flight controller. Meant...
thingiverse
Shelf for the front standoffs of the FPVCycle Glide / Hyperlite Glide. I use it to zip tie a capacitor, buzzer and receiver to it. ... Inspired by Richard Howarth's [ViFly Mini shelf](https://www.thingiverse.com/thing:4429902/files)
thingiverse
Especially since they were made longer to accommodate the larger stator of the new FPVcycle motors. I have hesitated to try this for a long time as I want to keep the weight down as much as possible. But, replacement arms are out of stock at this...
thingiverse
In these scenarios, I've had good results after scaling the model up a few percentages!) A shoe for your FPVCycle Prototype 5! (arm skid/guard/protector) These shoes will protect your arms and hardware from damage, as well as well give you ~6 mm...
cults3d
GoPro Session or Runcam 5 mount for the FPVCycle/Hyperlite Glide. ... 30°.
thingiverse
Remixed this antenna mount to fit FPVcycle Prototype 5 and Fouride frames
thingiverse
DJI Air Unit mount for FPVCycle Prototype 5. ... 30x30 holes to mount to frame
thingiverse
Immortal T mount for the FPVCycle Glide. ...Fits on the front and the back.
thingiverse
Simple 20 degree angle fixed mount for most FPVCycle frames (Glide, Incisor, Fouride, etc). ... Slot in the back for power.
thingiverse
Remixed to fit in the FPVcycle Prototype 5 and Fouride frames. ... Added stubby O3 version Added stubby Vista version
thingiverse
A remixed design for the Gopro Hero 8 to mount to the FPVCycle CineSplore, CineGlide, Or Fouride frames. ...Has space for a glass ND filter Mount is set at 15 Deg