fpv rc plane 3d models

My attempt to design and print RC Plane Wheels and Tyres (or Tires) resulted in a range of options for users. Tyre sizes come in 2 and 3 inch outer diameter, with both wide and narrow formats available. Rims are also produced in wide and narrow...

To build your plane, obtain the plans from Brooklyn Aerodrome or Make Magazine's website. Mount these servo horns on the elevons using double-sided tape and zip ties; consider utilizing the forwardmost hole to adjust elevon position when controls are...

Reorient to prepare for R/C plane deployment.

I started recently printing RC planes, and quickly need a way to store them. As a renter, drilling into the ceiling is not a great option, so I designed these to use command strips.<br><br>I also used a bit of weather-stripping to pad them. There is...

Sorry for the inconvenience, but due to the administrative neglection of Thingiverse this site has become too buggy to be trusted anymore. ---------- RC plane models (especially motorized models with a landing gear) demand a lot of storage space...

Complete cockpit for rc airplane WW2 fighter scale can be change before printing with %

Complete cockpit for rc airplane WW2 fighter scale can be change before printing with %

RC plane models (especially motorized models with a landing gear) demand a lot of storage space when not in use. Plus, the place where you store them must be child-safe (cat-safe, dog-safe...). And, on top of that, plane models don't last forever,...

This is a canopy I built specifically for my FliteTest FT_Spitfire RC Airplane, which can be found at https://www.flitetest.com/articles/ft-spitfire-build. You can see the finished product in action here: https://www.youtube.com/watch?v=wmXtP1M0wGs....

VERSION 4 - MAY 2021 Update - Full Airfoil / thicker wing / similar to ClarkY - 2-piece Canopy for easier printing - Improved profile Ailerons - Removable landing gear anti-rotate tabs - RECOMMEND - Half Travel on Elevator All STLs refreshed...

UPDATE 13 Sept 2022 SPLIT Wings and Rear Fuselage Allows all bits to fit on 220x220x200 printer Note: Wing1 should to be diagonal to fit on bed VERSION 3 - MAY 2021 Update Full Airfoil / thicker wing / close to ClarkY 2 piece Canopy for easier...

This is the first rc aircraft design, a 1000mm span aerobatic plane loosely based on geometry from the Yak54. It's still a work in progress, but it flies smoothly and properly. My initial prototype was printed with PLA. Assembly should be fairly...

i picked up making rc airplanes after stumbling on to the flite test youtube channel so ive made quite a few of there planes from foam board, i was trying to do it as cheaply as i could so only spending money on stuff i absolutely had to. it was also...

Hello, The original plan for this RC model plane originated with Andrej Pervinsek. It was designed for building an air combat model using balsa and plywood, equipped with a nitro engine. I converted the model into onshape format, allowing it to be...

special created for my fpv glider.did have a mount becose don't wonne put te cam in te nose of my glider.thats wy i created this mount for the caddx vista pro.

My attempt to design and print RC Plane Wheels and Tyres (or Tires) Tyre sizes are 2 and 3 inch outer diameter, in both a wide and narrow format Rims are also in wide and narrow format, with either 3mm or 4mm holes for axles. Tyres where done as my...

The design enables a similar tail connection like the one found on the Hobby Zone Firebird 2 RC airplane, which tilts the tail section. ...It's perfect for experimenting with foam RC aircraft tails or any other innovative project you can imagine.

This is a plane created using 3D printed (regular PLA) and 5 mm foam board to get the best of both materials. I have been printing planes for a while and fin out they are quite heavy and not easy to fly. I had this idea to create a very easy to...

... the incoming beam relative to a reference plane. ...To measure this, a protractor or an angle measuring device is used, positioning it so that one edge aligns with the reference plane and the other edge touches the incoming ray at its point of impact.

Because there where no wheels for the Ramiel indoor plane included so I created them myself. Print in PLA or PLA-LW. ... Axis is 0.575mm - use a carbon or metal rod for this Combine it with my indoor wheel:...

RC pilots take flight control to a new level with a high-performance front-wheel steering arm and mount that delivers precise handling and maneuverability to their scale aircraft.

... little tips. ... This is a fairly lively and very playful aerobatic plane, which will fully satisfy both experienced and intermediate pilots, who are looking for a good scale aerobatic plane at a lower cost. ... Span : 1000mm Weight : 1,2 to 1.4Kg

Flying high on my plane, I'm constantly thwarted by a worn-out rubber band holding its wings in place. ...Determined to soar free, I design a new one, crafted from durable NinjaFlex material - and suddenly, life takes flight!

My first LED lights night plane. The idea was to make it similar to the historical Valkyrie aircraft. You can see how the construction goes from scratch in the video... ... Video https://youtu.be/nSL6wrx8yb4

... size GoPro 3+ and board cam that measures just 32x32mm. ...These tiny cameras will fit snugly into the camera mount. Check out my detailed build log at http://fpv.no/vbulletin/showthread.php/7807-FpvCat-Byggelogg for more information on this project.

It is usefull if you have a plane transmitter (4/5/6ch) and want to use it as a RC Car transmitter (2ch). I'm kind of old school and have never been able to adapt to wheel transmitters for RC Cars. I wanted to be able to use the same transmitter...

This is a landing gear for RC airplanes designed to work with 1/10 scale RC car shock absorbers similar to those ones: https://www.banggood.com/4PCS-100MM-Front-Rear-Shock-Absorber-Damper-108004-Upgrade-for-1-or-10-HSP-RC-Car-Parts-p-1280176.html...

This is a custom housing for the Immersion VTX on my Volantex Ranger 1600 FPV aircraft. The base grips securely onto the fuselage, and I secured it using Loctite plastic bonder epoxy. The transmitter fits snugly inside; I leave it slightly loose for...

I required some wheels for my Fokker Dr.I RC model, so here we go. Simply print the part twice and assemble the two components together. For the tire, you may use a rubber hose, or what also functions exceptionally well, sealing cord (is notably...

This is a complete hardware set for the Twisted Hobbys Yak 55 RC airplane. The factory parts came in white, but I wanted black, so I modeled these in Fusion 360. ... This also includes a jig for cutting a centered slot in the rudder for the tail skid...