formd t1 fans 3d models

A simple duct for the top exhaust fan in the FormD T1 case, tested with Arctic p12 fans, should work with other normal sized 12cm fan..

Remix of this file to work with the Phanteks T30 Fans: https://www.printables.com/fr/model/451314-formd-t1-11-120mm-noctua-nf-f12-pwm-fan-duct

Some motherboards are rubbing fan on T1 this shroud is designed to avoid that, it directly screw down underside of fan bracket, make sure that narrow side fits between struts (narrow side is flat, but wide side have concave) Dimensions 120x115x1.5mm

Fan Duct for a 92mm fan. ...Designed for the FormD T1 case when using a 92mm radiator at the end of the GPU. ... Prevents hot air from recirculating back into the case.

This is a short 92mm fan duct designed for a FormD T1 case that utilizes a 92mm radiator at the end of the GPU. ...This duct helps force hot air out of the case rather than have some of it bounce off the mesh side panel and recirculate back into the...

This is my design for the formd T1 pedestal (or feet), with cutout to mount a 120mm slim fan as bottom exhaust If you have a large 3D printer, you can print it in one go, or print separately on a smaller 3D printer, I used super glue to attach them...

a4x20 기준 2.5slot 까지 가능 a - 정방향 나사 배열 b - 램쪽으로 더 붙는 나사 배열 ※z690i rog strix / axp120x67 히트파이프 오른쪽 기준

This is a bracket for a 40mm fan to help keep the chipset of the asus x570-I ITX motherboard cool. ... I used 4 screws to hold the fan in with small nuts on the back of the fan. ...The fan in the picture is a noctua 40mm fan.

This is a fan duct designed to fit on a 92mm fan. ...The Dan Case fan duct is 10mm tall, this one is 13mm tall to create a better fit when used in the Formd T1 case. It has not been tested yet. ... Print from the bottom up, no supports needed.

This model is based on eedev's fan frame with the pogo pins on the side. In my case i didn't need the cutouts for the pogo pins as I was using the original cables and it was harder to print with supports in PETG. ...So I removed the cutouts, changed the...

M19 to M16x1 Adapter for FormD T1

19mm Plug for FORMD T1. ... Designed and tested for .2mm layer height PETG. Buyable here: https://j-hackcompany.com/?product=formd-t1-19mm-plug

formd t1 fitting at back of case you must change 100% -> 105% in slicer

Front shells to customize colors on FormD T1. ...Maybe you want to see what a 2 tone FormD T1 will look like? Maybe you want to see a different color? Bonus: protects your case from scratches and fingerprints! ...I like to use silk PLA for this.

This is a small post to aid in cable management in the FormD T1 SW. It is designed to slot into the fan brackets. Simply insert the post through a fan bracket slot and then rotate the post 90° to make it fit snug against the bracket. You can...

This is a replica of the stock FormD T1 power button. Note that I designed this to fit with the T1 SW v2, though it might work with other T1 versions (I haven't tested them). ... The NX *.prt file is provided if you want to customize the design...

I reverse engineered the front panel of the FormD T1. I have uploaded the STL for direct printing and CAD files to mod. And yes, Wahaha360 gave me permission to share this reverse engineered T1 front panel :) Ideas to try: -Add your own front IO -Add...

These brackets help better support the PSU in the FormD T1 SW across a few configurations. There are definitely more combinations of T1 slots and PSU stand-off lengths not included here, so the NX *.prt files are provided if you want to customize the...

Custom Front Panel for the FormD T1 adding two USB type-A ports. ... https://www.aliexpress.com/item/32864802403.html?spm=a2g0s.9042311.0.0.27424c4d81qOcg You'll need one of those.

The FormD T1 has a large gap in its rear panel when configured in a 2.25 slot configuration. This cover closes that gap. See Post-Printing section for installation instructions. Note that I designed this to fit with the T1 SW v2, though it might...

Required: FormD T1 v1.1(unsure about other versions) XSPC TX240 Noctua A12x15, rubber pads removed, with countersink screws/grub screws/tape/or just sitting on top; there's no room for screw heads sticking out. ... 6-32 screws of 1/4" length, for...

The case in the image is a FormD T1. There is a recess at the bottom of the feet designed to fit felt pads to protect your desk. ... These are the pads I used:...

These are two different feet designs I made for my FormD T1 ITX build. They have a recess in the bottom for some felt pads to protect wooded tables etc. ... These are the felt pads I used for the feet:...

Case feet for FormD T1 to give more clearance beneath PC. Scan of human foot gives creepy (or adorable) look to your PC while keeping airflow to a maximum. Use m3 screws. Printed at 20% infill but you might require sturdier feet. ...Post your builds and...

The NX *.prt files (for the variety of SSD mounts as well as the reference FormD T1 v2 Front Panel and Samsung 850 Pro SSD) are provided if you want to customize the design further. ... [1]:...

I designed an extension to the side panel of the FormD T1 v2 Reference case, so it can fit my AMD Radeon RX 6900 XT graphic card. It adds 7.9mm clearance to the side panel. I had to replace the screws holding the side strut (2xCSM3-8) and the AIO...

These are a USB 3.0 port mount and momentary switch mount that fit in the slots in the back plate of a Formd T1 case. ...Designed around these specific products from amazon: ...

The power button PCB that came with my FormD T1 SW had an issue where the PCB's wire "glue" (probably for strain relief) interfered with the button when it was pressed. This design adds "notches" to the button so the interference is removed. I also...

You will need a long M3 screw and nut in order to mount the bracket to the mount. ...The longer screws that came with the T1 work well in securing the mount to the case.

A 3D model of the FormD T1 v2 reference backpanel. ...Measures maybe not fully accurated, taken with a ruler and a regular caliper.