formbot voron 2 4 r2 manta m8p wiring 3d models

Needed mounts for the new Manta M8P for my Voron 2.4r2 build and couldn't find an existing one so worked up this design.

Sized to fit a printer with a 400x400 build plate as per the Voron 2.4 Configurator.All parts were created by Voron Design and have been released under the GNU General Public License v3.0Original files can found on the Voron Design...

This Left drive is made of 2 aluminium plates with  plastic shims in between.The alu plate is 4 mm stickness. ...Some holes (diam 2.5 mm) should be threaded for M3 screws.The Alu plates are not extended on Y Aluminum Slot to allow some gantry flex...

Wanted a clean wire management solution for my voron 2.4. This is for a 350 build, but the f3d file is included so you can modify to your needs. These print flat, and then fold up to form the U channel. I apply a little super glue to the fold to...

Vorderer Bett Abstand 38mm um zu vereinfachen, das ihr das Bett im richtigen Maß und parallel anbringt einfach dieses Tool 2 mal ausdrucken und anhalten oder, noch besser, mit je einer M3x12 er schraube und einer Hammer t Nut aus dem Voron-Set am...

replace the chain rail end from 3 holes into 2 holes for VORON 2.4 FORMBOT kit

Hello! ...This is cradle for Orange Pi Pc plus for Voron 2.4 R2. ...I didn't find any stl in vorondesign project and in github, so, i designed my own cradle.

Hello! ...This is cradle for Orange Pi Pc plus for Voron 2.4 R2. I didn't find any stl in vorondesign project and in github, so, i designed my own cradle. ... more on: https://vk.com/molnija3d and https://www.molnija3d.ru

My Voron V0.2 Formbot kit had a longer reset button on the display wich bend up the original lever ending in a constant reset. Had to break it free to continue to use my printer. ...This model has a hole in it for the button to fit in.

A light weight case for the manta m8p, uses ~40 grams of plastic. ...You need 8 m3 bolts.

Drag chain washers to help with securing the ends of the ones included in my Formbot kit. ...The one with the slot is meant to pass a ziptie through to help secure the wire bundle at the chain end.

This is OV9726 usb camera mount for Voron 2.4R2. It is a 50 degrees FOV camera. ... more on: https://vk.com/molnija3d and https://www.molnija3d.ru

Use recommended Voron print settings.

it is intended to be mounter from the bottom of the base, screwed to from from underneath(It may well work on other printers that are of similar construction).After feed back from those who made the MK1 version, this full re design now uses a...

Designed this model to hold and support the BigTreeTech Manta M8P boarduses the 4040 extrusion and T-nuts to secure it to the sides and back but will utilize the existing holes for cable management. It will be slightly tight to install it's...

Groundplate for Bigtreetech Manta M8P

BIGTREETECH MANTA M8P V1.0

I needed a board mount for the Manta M8P.Thank you @Byte Insight for the Step Files

I decided to finally upgrade my Anet A8 (now a metal AM8) to have a Manta M8P as the controller board instead of the stock fire hazard Anet board. However, I could not find any simple mounts for this board that screw into extruded aluminum anywhere...

Mount to fit a M8P under a EnderWire.... ...cause why not.

FYSETC VORON 2.4 R2, Trident OR 0.1 hollow CNC gantry fixed block， this printed part is suitable for FYSETC Full metal gantry. ... Go to buy link ：...

An enclosure for BigTreeTech Manta M8P board

This model is an evolution of “Rama’s” idlers with a more efficient cover system to improve the stability of the screws that's provide the tension.=> Better quality and stability of the XY belt tension. To be use with 5mm stainless steel rod.Same...

This is part from : https://www.printables.com/model/247919-bigtreetech-manta-m8p-enclosure/files

Because the CB1 adapter board is curently not working and is being replaced by bigtreetech, untill that arrives i adapted the original Bigtreetech voron DIN rail mount for the Manta M8p to attach together with a pi 3B+ This has been tested and...

NEW MOUNT HERE: https://www.printables.com/model/877941-manta-m8p-din-mount-v2-low-profileThey are used to mount the BTT Manta M8P Board to a DIN rail on a low-profile mount.

BOM : M3 x 30 SHCS - 4 M3 x 5 SHCS - 4 M3 x 4 Brass heat Insert - 8 M5 x 4 Brass heat Insert - 8 80 mm CPU Cooling Fan - 2 M5 washer - 8 M5 x 40 SHCS - 4 On the bottom of the enclosure there are 4 brass inserts (M5 X 4) to attach the din rail...

For cooling the TMCs on the Manta M8P. I tested it with BTT TMC2209 and sunon 5015. Print it upside down. ... Thx to: https://www.printables.com/de/model/105849-octopus-v11-cooling-tmc

Voron 2.4 钣金电机座适配打印件

Voron 2.4 3D Printer