ford mondeo parcel shelf holder 3d models

I Replaced The Broken Parcel Shelf Holder In My Car With A Custom-Made One I Designed And 3D Printed. You Can Also Create Your Own Using The Rhino Source File Provided, Which Includes Modifications To Suit Your Needs. To Get Started, Simply Follow...

This is a replacement mounting peg for the parcel shelf in a Ford Focus from 2013 to 2016. Print Settings: Printer: Mod-t Rafts: Doesn't Matter Supports: Yes Resolution: High Infill: 50% Notes: You will want to use at least 50% fill. At 20%...

Glovebox holder for MK1 and MK2 Ford mondeo (1993-2000). ...My design

These clips are used on the tailgate of the Ford Fiesta Mk5 and the Ford Fusion to attach the parcel shelf cords. They are suitable for the models: Ford Fiesta Mk5 (2002-2008) and the Ford Fusion (2002-2012). ... To put them in place, first put them...

Ford 2423830 Parcel Luggage Shelf Clover shaped part. ...These break a lot because there a bad design by ford but its the only design that fits so print multiple spares.

Mount for loudspeakers in ford escort

This is to replace the brackets on a Ford Focus parcel shelf. The existing brackets come off over time and refitting them doesnt really work. This saves replacing the whole parcel shelf which quite expensive. The orginal clips work by gripping...

Ford Mondeo MK4 - arm compatible with gogen holder

I duplicated the design of the clips used on the Ford Mondeo and other models, which attach to the parcel shelf of the vehicle. ...Mine had broken, so I replicated theirs.

A second version of the Mk3 Ford Focus Parcel Shelf Bracket, a little bit closer to the original Ford part although as with the V1 the measurements and dimensions are approximated will do a Version 3 when I get the chance to measure an original...

Ford Fiesta Parcel Shelf Hinge Clip Replacement. The replacement clip consists of an external and internal component. Both parts are secured together by screws, with the rim of the shelf fastened between them. The M3x15mm screws and nuts hold...

This is a clip that broke in my Ford Fiesta (~1998), it is used in one of the parcel shelf strings (see pictures). This item is designed to be printed without support, only with a Brim to make it stick better to the heat-bed and in fact it printed...

Not printed this yet would be interested if it fits all measurements are approximated but the large piece goes on the underside of the parcel shelf clipping into the studs, the small piece needs two little holes drilling and is pressed through from...

This is a direct replacement for the stud that holds up the Parcel Shelf in the Mk3 Focus Hatchback. It should fit STs or whatever other hatchbacks. It should be a tighter fit than the OEM part, so it shouldn't fall out as easily as the OEM part,...

Ford Mondeo MK5 front parking sensor holder DS7315A862AB DS7315A862

a "good enough" replacement part for the CV6Z5846538A peg that goes in the back of a Ford Focus 2012-2016ish Hatchback. ... might have worked better to shrink the part that sticks into the car, by a mm or so, but this worked good enough.

The Ford Mondeo MK4 is equipped with an arm that's fully compatible with the Gogen holder, allowing drivers to use their preferred accessory with ease and convenience.

A replacement for the parcel shelf clips that fits a 2001-2005 Honda Civic and other cars with a 10mm stud to hold up the shelf. To install it, simply cut off the old clip, thread the cord through the new one, tie a knot in it, and you're done. ... ...

This is a cellphone holder for a 2017 Ford Fusion / Mondeo, it's really sturdy. You'll need an old cellphone holder to take the cellphone holder mechanism. I used this old baseus, the socket uses a 17mm ball, it's attached using a 4 mm screw. No...

A Simple Mount Plate Designed Exclusively for the Mondeo mk5 Car Model. ...To Secure It Properly, You Will Require One M5 Screw That Acts as a Positioning Pin.

This is a simple hinge for the parcel shelf for a 2012 Ford Focus (MK3) or Ford Fiesta. The original bracket often brakes, so did mine. The cardboard-like material was so damaged, that i had to make a completely other way of connecting the hinge and...

I designed a replacement part for my 2012 Ford Focus's worn-out parcel shelf hinges, specifically targeting the inner (center) component. My goal was to create a larger surface area that can be securely attached to the possibly damaged parcel shelf...

Ford Mondeo/Fusion car phone mount installed on center console cup holder.

The Fitting Adapter for the Ford Mondeo Engine F3R Filter

... In this post, you'll find four STLs: * Ford Mondeo MK4 Console Cover Left.stl This is a plain coverplate for the Mondeo MK4 that can be used for all purposes, like a replacement cover, or to use as a template for other phone holders or accessories.

I have prepared Ford Mondeo Mk2 for 3D printing: 3D--> yaro.pro(Burned car 01)sketchfab.

I have prepared Ford Mondeo Mk2 for 3D printing: 3D--> yaro.pro(Burned car 01)sketchfab.

I Designed a High-Performance Ford Mondeo Using Inventor, Check Out My Video Tutorial Here: https://www.youtube.com/watch?v=F9XNVGC2P88

This is a replacement component designed to repair a faulty 1999 Ford Mondeo left-hand driver's power window switch, specifically engineered for European models.

For better strength print horizontal and use supports.