ford maverick lights 3d models

This is a heated/cooled cupholder for the Ford Maverick. It works by pumping heat out of the air around a beverage using the car's HVAC system. It mounts to the FITS slot and requires other non-3D-printed hardware to work: Two 120mm PC radiators with...

What's better than one Magsafe station in the backseat of that Maverick? ...Obviously TWO!

"No-supports" remix of a trash bag holder frame designed to press into the rear FITS slot between the seats in the 2022 Ford Maverick. I used Autodesk Meshmixer to slice the bottom part flat so it could be printed without supports. The original...

I just added the ford block letter logo to the original design, nothing else changed. ... Printed with the logo side down with no supports.

... supports so I made a small change to remove it. As well as give it a completely flat bottom. Use some velcro or double sided tape to keep it in place. Enjoy Maverick Fam! ... OG credit goes out to https://www.thingiverse.com/thing:5436083

What's better than one Magsafe station in the backseat of that Maverick? Obviously TWO! Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .20 +-.4 variable Infill: 25% lightning (Do Cubic for strength...

What's better than one Magsafe station in the backseat of that Maverick? Obviously TWO! Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .20 +-.4 variable Infill: 25% lightning (Do Cubic for strength...

Have too many FITS adapters for your Ford FITS slot? Some of them are actually handy to have in your garage? Well, look no more. ...Just slap a couple of these up and boom, you've got them all on display / and or usable format.

Talk about convenience! To be used with the Ford FITS cleats, and goes great with the cubby insert.Highly recommend printing this with at least PETG, but more preferably ABS or ASA to stand up to the high temps that the interior of cars can reach. ...No...

Have too many FITS adapters for your Ford FITS slot? Some of them are actually handy to have in your garage? Well, look no more. Just slap a couple of these up and boom, you've got them all on display / and or usable format.</p> <h3>Print...

You can read more about it here: * https://www.thedrive.com/tech/its-time-to-vote-on-the-drives-best-ford-maverick-3d-printed-accessory * https://www.thedrive.com/tech/i-3d-printed-a-heated-and-cooled-cupholder-for-the-base-ford-maverick *...

This was developed for The Drive's Great Ford Maverick 3D Print-Off where auto journalists Rob Stumpf (@RobDrivesCars) and Peter Holderith (@_baldtires) spent two weeks building accessories for the Ford Maverick's FITS system.You can read more about...

This is a replacement cover for the 12v DC panels in the truck bed. I made these so you don't have to drill or mess up the OEM ones if you want to use the 12v lines in the bed. I printed this on a Creality Ender 3 with eSUN PETG using the following...

This is a replacement cover for the 12v DC panels in the truck bed. I made these so you don't have to drill or mess up the OEM ones if you want to use the 12v lines in the bed. I printed this on a Creality Ender 3 with eSUN PETG using the following...

This is a pair of seat hooks to hold bags (obviously) and a bar with a FITS slot on it. I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate Temperature:...

This is a bar with a FITS slot on it. This is designed to slot into the bag holders I made. I put a little screw on each end so it doesn't slide out - gonna add holes eventually. I printed this on a Creality Ender 3 with eSUN PETG using the following...

<p>This is a bar with a FITS slot on it. This is designed to slot into the bag holders I made. I put a little screw on each end so it doesn't slide out - gonna add holes eventually. ...I printed this on a Creality Ender 3 with eSUN PETG using the...

This is a pair of seat hooks to hold bags (obviously) and a bar with a FITS slot on it. I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate...

These are left, and right-side frame mounts for the Parajet Maverick Paramotor and fits SpeedTech Lights Flare 360 LEDs available on Amazon. I used flexible TPU filament. Each support is marked (P)ort or (S)tarboard, designed for a red light on the...

Power for the bed column, right inside the cover. ... This is the outlet I used with the cap: https://www.amazon.com/dp/B07BT4SHFY?ref=ppx_yo2ov_dt_b_product_details&th=1

Wanted to create a bed rail clamp that I could hang my ice scraper / brush from in the winter. This would allow it to hang dry and not get the interior seats/floor all wet. This is technically a remix of two different other designs... took the...

My Opel Carsa UTE do have a cup holder but it is so small and shallow that when I go around a corner it falls over and when I installed a speaker box at the back it slightly covered up the cup holder, the doors sort of have cup holders but then I...

Similar to my other FITS slot adapter but this sits flush with the rest of the console. Some people would like to plug this slot so dirt and debris do not get into it. This is the perfect match for that purpose. Fits tightly into the slot. If it's...

This is my prototype for a slip cupholder, it is meant to "clamp" onto a bottle to hold it in place, I modeled it around a 12 oz soda

Real simple print. Uses approximately 128g of filament. Recommend PETG for the heat that can accrue in vehicles. Update: 7/5. Adjusted rear angle to sit more level in console. ... Added a ledge in middle pull for easier grip with fingers.

Just added an additional divider and a hole to the existing model. I frequently use my center console as trash for receipts. ...With the hole, I can drop trash below without removing the tray each time.

Tail light cover clip for ford mondeo mk3

This is an umbrella holder that lives in the back seat. I designed this to work with a FITS slot in the rear cubby. I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature...

This is an sunglasses holder that lives in the front FITS slot adapter. I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate Temperature: 70 The...