ford maverick dash cubby 3d models

Have too many FITS adapters for your Ford FITS slot? Some of them are actually handy to have in your garage? Well, look no more. ...Just slap a couple of these up and boom, you've got them all on display / and or usable format.

Have too many FITS adapters for your Ford FITS slot? Some of them are actually handy to have in your garage? Well, look no more. Just slap a couple of these up and boom, you've got them all on display / and or usable format.</p> <h3>Print...

You can read more about it here: * https://www.thedrive.com/tech/its-time-to-vote-on-the-drives-best-ford-maverick-3d-printed-accessory * https://www.thedrive.com/tech/i-3d-printed-a-heated-and-cooled-cupholder-for-the-base-ford-maverick *...

This was developed for The Drive's Great Ford Maverick 3D Print-Off where auto journalists Rob Stumpf (@RobDrivesCars) and Peter Holderith (@_baldtires) spent two weeks building accessories for the Ford Maverick's FITS system.You can read more about...

I designed this to work with a FITS slot attached to an adapter that fits in the cubby hole on the dash. I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer):...

I designed this to work with a FITS slot attached to an adapter that fits in the cubby hole on the dash. ...I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80...

This is a pair of seat hooks to hold bags (obviously) and a bar with a FITS slot on it. I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate Temperature:...

This is a bar with a FITS slot on it. This is designed to slot into the bag holders I made. I put a little screw on each end so it doesn't slide out - gonna add holes eventually. I printed this on a Creality Ender 3 with eSUN PETG using the following...

This is a replacement cover for the 12v DC panels in the truck bed. I made these so you don't have to drill or mess up the OEM ones if you want to use the 12v lines in the bed. I printed this on a Creality Ender 3 with eSUN PETG using the following...

<p>This is a bar with a FITS slot on it. This is designed to slot into the bag holders I made. I put a little screw on each end so it doesn't slide out - gonna add holes eventually. ...I printed this on a Creality Ender 3 with eSUN PETG using the...

This is a pair of seat hooks to hold bags (obviously) and a bar with a FITS slot on it. I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate...

This is a replacement cover for the 12v DC panels in the truck bed. I made these so you don't have to drill or mess up the OEM ones if you want to use the 12v lines in the bed. I printed this on a Creality Ender 3 with eSUN PETG using the following...

Wanted to create a bed rail clamp that I could hang my ice scraper / brush from in the winter. This would allow it to hang dry and not get the interior seats/floor all wet. This is technically a remix of two different other designs... took the...

My Opel Carsa UTE do have a cup holder but it is so small and shallow that when I go around a corner it falls over and when I installed a speaker box at the back it slightly covered up the cup holder, the doors sort of have cup holders but then I...

Similar to my other FITS slot adapter but this sits flush with the rest of the console. Some people would like to plug this slot so dirt and debris do not get into it. This is the perfect match for that purpose. Fits tightly into the slot. If it's...

Power for the bed column, right inside the cover. ... This is the outlet I used with the cap: https://www.amazon.com/dp/B07BT4SHFY?ref=ppx_yo2ov_dt_b_product_details&th=1

Real simple print. Uses approximately 128g of filament. Recommend PETG for the heat that can accrue in vehicles. Update: 7/5. Adjusted rear angle to sit more level in console. ... Added a ledge in middle pull for easier grip with fingers.

Just added an additional divider and a hole to the existing model. I frequently use my center console as trash for receipts. ...With the hole, I can drop trash below without removing the tray each time.

This is my prototype for a slip cupholder, it is meant to "clamp" onto a bottle to hold it in place, I modeled it around a 12 oz soda

This is an sunglasses holder that lives in the front FITS slot adapter. I printed this on a Creality Ender 3 with eSUN PETG using the following settings: Print Temperature: 245 Plate Temperature (Initial Layer): 80 Plate Temperature: 70 The...

The sleek lines of a Ford Mustang take center stage as you navigate through the winding roads, but what about keeping your iPad Mini safely secured while driving? ...For models from 2011 to 2014, there's a clever solution waiting for you - a dash mount...

I've crafted a mount point for Phone Holder for the Ford Focus 2019-2020 -> The mount perfectly mirrors the side of the dash's shape. I employed Photogrammetry to scan the dash and model the holder accordingly. Some high-quality double-sided tape...

dash

So that the center console does not have to be disassembled and magnets have to be glued behind the center console, there are holes for suction cups on the back of the dash mount, which can be removed at any time without residue (holes for magnets...

The small trim pieces on my 1997 OBS Ford F350 broke off (see pictures), so I modeled some insert tabs to replace them so I could re-attach my trim piece. If you can use them, enjoy. PLEASE NOTE: I turned the piece on it's side to slice. ... This...

The design's base parts can accommodate a wide variety of devices, including GPS and dash cams, by easily swapping out the cross bar and/or phone clips. I initially printed this mount using PLA, given the current winter season. However, once spring...

This part makes the closing mechanism of the rear armrest pocket work again. ...3D print it or simply file it off a piece of plastic you have lying around.

:D This should be the last Switch Mount you need for your Ford Maverick. It's solid as a rock, even when just being printed with lightning infill to take photos of it. Heh A huge thanks to everyone's remixed items. ... https://youtu.be/E-1Uux7CauM...

I used the FITS adapter to add a trash bag holder. ...I suggest printing with PETG as PLA may deform in the summer months.