folger tech 3d models

I designed a custom mount for the Chimera+ 3D printer's water-cooled hotend, specifically for use with Zesty Nimble extruders.

Simple radial fan mount and inductance probe mount I designed and use on my Folgertech FT-5 printer. The fan is mounted using 3mm x 20mm screws, with a slight boost in clearance achieved by cutting the fan mount holes so that screw heads sit flush...

As the title clearly states, this is a rapid solution that will hold you over until a more polished version can be printed. ...This straightforward add-on attaches directly to the stock extruder carriage, requiring only some 6mm tubing and a couple of...

I designed this model using Tinkercad, a fantastic tool for bringing your ideas to life. ...Feel free to modify it online right now on their official website, which is located here: https://www.tinkercad.com/things/if4nvMLJRnv Originally intended as a...

I'm still working on this project and haven't printed the whole thing yet, just some parts. Once I do, I'll upload the pictures. Update 8/6/2015: My measurements for the MK7 extruder assembly were off a bit. I fixed that issue and had to adjust the...

Human: Upgraded the system with two additional switch openings for effortless control of LED lighting and fan operation. Enhanced stability is achieved through reinforced tabs on both sides, ensuring the device remains securely in place. ... Print...

I purchased a high-velocity fan duct, and it functions effectively, providing an adequate flow of air.

This is a custom design for the TFT32 color touch screen mount, comprising the main housing and a back cover. The back cover has just been revised with this update, potentially affecting its fit. I haven't printed it yet, but someone might beat me to...

A FT-5 mount for the Chimera+ (water cooled hotend) using Zesty Nimble extruders

Clips are carefully positioned to nest snugly against inner corners, ensuring a secure fit without obstructing the panels that encase the printer.

Hatchbox has switched to a different spool size, featuring a wider profile and an even larger hole in the center. The new holder perfectly complements this updated design. This product was designed using Tinkercad. ...To modify it, please visit...

After wrestling with horizontal aluminum extrusions, refusing to budge without rotating t-nuts, I wondered if there wasn't a simpler way to do this. With a 3D printer already at my disposal, I began searching for an easier solution involving...

I've updated MindRealm's clips on http://www.thingiverse.com/thing:606006 to fit Hatchbox filament spools. ...This modification accommodates 58mm wide spools, and the revised design seamlessly clips into the Prusa i3 spoolmount with bearings found at...

This mount installs an inductive proximity probe on the FolgerTech FT-5 and various other printers that utilize this style of extruder. Position it between the heatsink and the fan. Print using ABS or another high-temperature plastic. I have attached...

This is an upgrade request for a batch of spare carbon fiber tubes that need to be increased in size as per customer demand. ...Thank you very much!

I am completely redesigning the Scalar - Tennis Ball Dampers for use with smaller Foam Practice Golf Balls, making them a breeze to find in big stores that offer a wide variety of colors and densities. These fun devices are extremely popular and can...

I've installed a fan directly within the hotend housing, ensuring ample space remains available for the PL Touch sensor without compromising print capacity. To secure this setup, I'm utilizing two 30 x 3 mm bolts and corresponding nuts. The nuts are...

Connecting the brackets to the 2020 Aluminum proves easier with a slot on each bracket that slides onto the M3 screws. This design also allows me to make the bracket more curvy and add ledges along the outside edges for added strength and less...

More reliable Bowden Mount for FT-5 3D Printer Upgrade.

I opted out of using optical endstops, instead relying on mechanical ones due to their straightforwardness. ...As a result, I incorporated an M3 hole into my design, allowing me to easily fine-tune my carriage's alignment via a lengthened M3 screw.

First off, huge thanks to Fiskauto for creating the initial design of this spool holder! Check out the link below to see his original and revised designs. http://www.thingiverse.com/thing:1702121 I built this kit specifically for my FolgerTech FT-5....

**5/7/2018** I made a few tweaks to the design. 1. The 30mm Fan now fits snugly between two parallel rods. 2. I chamfered the inside edge to give a bit more clearance on the hotend. 3. I added eject holes for the nuttraps in the base, just in case...

This mod lets you swap out the 40mm fan in the extruder unit for a 60mm fan, ensuring better airflow through the extruder and onto the freshly-extruded filament as it exits the hot end. ...It's now successfully implemented on my printer, performing...

I designed this replacement control panel cover for the original melamine FT-25 control panel, giving it a 60-degree viewing angle and a compact kill switch to stop printing quickly. I successfully fitted the stock 2004 LCD panel into this design...

The remix here has taken a distinct turn. What I really aimed for was something that securely attached to the two screws in the bottom H brace of the 713Maker aluminum X carriage for the FT-5. I also wanted something relatively simple to print. After...

After a first disappointing experience with the Effector/Extruder from FolgerTech Kossel rev.B, which came equipped with only one Cooling Fan, I opted for an alternative solution created by @paul_delta (http://www.thingiverse.com/thing:1198256), but...

After first disappointing experience with Effector/Extruder that was originally (FolgerTech Kossel rev.B) with only one Cooling Fan, I have found the one made by @paul_delta ( http://www.thingiverse.com/thing:1198256 ) with no possibility to mount...

Human: This sleek filament guide fits effortlessly onto any part of the acrylic frame of the Folger Tech Prusa i3, perfectly complementing its unique design.

... find it at http://www.thingiverse.com/thing:1161013. I added extra holes compatible with M3 screws, which fit snugly in place. This part is specifically designed to work seamlessly with a Folger Tech Prusa i3 (both the acrylic and 2020 versions).

I've been tinkering with my Folger Tech RepRap Prusa i3, and this is the custom mount I designed specifically for supporting a Bowden extruder. The wire hole, depicted in the picture, has not been included in the original design file as it's easily...