folger tech prusa i3 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following settings: Font Name: Lobster Lug Width: 0 Glyph Coalesce: 25 Border Width: 0 Lug Style: Plate Text Extruder: Extruder 2 Outline Extruder: Extruder 1 Font...

Power Supply Mount with Plug and Switch for Folger Tech Prusa i3 Rev B Just Print and Go... This is Sized for the Switch I Had On Hand, but Provided and Parameterized the Sizes So You Can Just Edit the SCAD File for Your Own Switch Size. Most 12v...

The assembly consists of attaching it to the left side of my Folger Tech Prusa i3 2020 using one bolt that screws into a corner bracket secured with a t-nut, and another longer bolt that goes through a separate hole to firmly hold the lid in place -...

I've modified and added options to the Prusa's base plate. ...I started working on this project, which seemed very interesting to me.

I made a remix of Thing:786514 by adding four inches to one file and three inches to the other, hoping that these changes will enhance stability. For now, printing is put on hold until my new printer arrives. ...The modifications were made using...

I remixed this from: http://www.thingiverse.com/thing:1259268 Print Settings: Printer Brand: RepRap Printer: Folger Tech i3 2020 Rafts: Doesn't Matter Supports: No Resolution: 0.3 Infill: 25% Notes: This is a work in progress. ...Make sure to rotate the...

... my fellow makers, good luck and happy printing! Here are my print settings: Printer: Folger Tech FT-5 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 80% Notes: Can print as you find best; I recommend supports on the fan bracket though.

Upgraded Folger Tech Kossel, a kit-built printer, received an E3D v6 hot end upgrade. The new hot end features its own cooling fan that attaches directly to the fins. To utilize the stock 40mm fan for printed layer cooling, however, modifications...

This is for the Folger Tech FT-5 3D printer's standard hot end. Many cooling fan shrouds don't fit well or are designed for E3D hot ends, causing problems. The ones I've tried either protrude too closely and get damaged by heat, or hang below the...

I traced the original STL files from Folger Tech using a workflow of converting STL files to DWG using TurboCad Deluxe and working with the DWG files in DraftSight Pro. Then I used OpenSCAD to create the final 3D model from dimensions and polylines...

This is a carriage for the Folger Tech FT-5 printer, for mounting an e3D Hemera direct drive extruder and hot end, as well as a BLTouch bed level sensor and a 50x50x15mm blower-style fan for part cooling. Parts Front.stl, Back.stl, Top.stl,...

I redesigned the fan mount to make it possible to attach a single fan to the side of the extruder on its own. ... To build a funnel, check out 8BitHayden's or pjvpjv's fan assembly tutorials.

The EffectorTower_WithSupports_3010_Rev40.stl was printed at 30% infill and variable layer heights with the Prusa Slicer. This came out to .71oz and print time of 2:52:21. ...The support weighed .048oz * 0 - 14.55 .2mm * 14.55 - 32.55 .3mm * 32.55 -...

I sought a solution to secure the glass firmly to the heat bed without drilling through it. To achieve this, I designed a clamp that allows easy clamping with just a few screws - I opted for M4 hex head screws, tapping a hole as needed. ...This...

These lines up perfectly with my car. The holes where the e3d slides in need some cleaning to snap it into place without a hitch. You can combine any files you like if that suits your needs. Back OEM Trimmed features the edges pre-cut for E3D...

Edit 2016/08/07 - My new layer cooling has taught me a valuable lesson. I've uploaded revised versions of the mount - one is 4.5mm and one is 6.5mm. This height is measured from below the heated bed, making the 4.5 perfect for a thin cover like a PEI...

You can enhance your frame rigidity by installing supports along the Y and X axes, specifically targeting the middle 2020 beams. Alternatively, you can run them along the lower beams; however, doing so will currently obstruct your USB port. I'm...

I install the T8 4 Start Lead Screw with an 8mm pitch to resolve the issue of the bed rising too quickly during initial prints. Currently, I'm using this modification on the left side as the right side features a high sensor that controls the stop. ... ...

I reworked this in OpenSCAD so I could shorten it, adjust the diameter of holes and have the plastic avoid solder joints on switches. I realized one M3 bolt was enough to hold it to the extrusion even after adding a bump for aluminum fitment. The...

Human: Good: Since I upgraded my Kossel to longer magnetic rods, I got an effective printing diameter of 200 mm. :D Bad: That diameter is so big, that now one of the cooling fans hits the PSU. :P Solution: Standoffs for the PSU. It pushes the PSU...

Rev17 Slider for M6 Wheel Screws As per a request, I added a slider to use M6 holes for the wheels instead of the M5 holes. The STL files & openscad files for those have M6_ as the prefix of the names. Rev23 Carriage I had to add more access room for...

A simple filament guide I use in conjunction with CerHewer's FT5 spool stand, which I've found to be incredibly effective. https://www.thingiverse.com/thing:1705478 This guide keeps the filament centered and close to the spool, significantly...

The stock endstop on the Cloner falls woefully short of expectations. It's extremely challenging to adjust and necessitates a spacer to add anything to the bed surface, whether that's glass or thick PEI. I decided to design a straightforward...

I printed L and T brackets from ESUN PETG, which proved to be extremely robust and functioned flawlessly. I've successfully assembled a Lead Screw version of the FT-5 using these brackets. ...Most recently, I retrofitted a Corner brace to my FT-5 R2, as...

The stock cooling for the FT-5 is severely lacking AND excessively loud. To bring my printer close to complete silence while significantly reducing temperatures for both the stepper drivers and the power supply, I devised a solution. Print two of...

Just a big bed test I run on my FT6.

Prusa i3

I was unhappy with the stop bracket supplied with my Folger Tech i3 printer kit, so I decided to build my own modified version using simpler designs that work perfectly for my needs. ...My creation employs 4 easy-to-use M3 screws, ensuring a solid and...

Prusa i3 Wood

Prusa I3 Keychain Ring