foldable steps 3d models

This can be done in Octoprint through Settings --> EPROM Marlin Editor Plugin --> Steps. On the far right, under Extruder, change this value for the new Direct Drive. I use 415 and it works great. Be sure to test your esteps by extruding 100mm and...

Those steps are optional, but they do make the part look like one piece. it does look so good that you can't even tell it's 3d printed. You can see the texture in good lighting in one of the pictures on the floor. Electronics Connect all the parts as...

If you are not using the Zeus Nano, you can edit the .step files to fit your VTX or just kinda mush it in there and hope for the best.Suspend only the ESC part (there are two pieces in the stack) of the stack 2cm or so above its future spot in the...

Vertical gear moved further to the outside on that design. Update2019-03-29: added new Print-In-Place HighRes files V7C, successfully tested on Dark-Gold PLA from ICE (assumed worst case) Used following settings 0.6mm nozzle, 0.15mm layer height,...

Plenty of tutorials on YouTube…From the model shop you will need 2 propeller shafts - external diameter 6 mm length 211 (I used the 301-23 from RABOESCH)2 dual couplers (ca 53 mm)2 propellers (1 Right & 1 Left) with a diameter of 5 cm (I...

This remix of the Prusa mini extruder rear part with integrated filament sensor. You will need parts for this to work: parts which are in original filament sensor for Prusa:1x IR filament sensor1x cable for filament sensor1x steel ball 7...

Avoid getting glue on the upper half of the ring at this time.Wait till the back assembly has hardened and can be handled before starting the next step.To attach the front quarters to the back assembly, use epoxy resin again, but if using 5-minute...

It does mean more support material than if printed the other way.The arm I've printed face down, with supports. AssemblyStart by putting in the M3 nut in the hinge's axis (if it's too loose and tends to fall out of place, you can also do that...

To me the advantage of the army green PLA is if the paint gets scratched it will reveal green rather than some random color.I used the stock Prusaslicer 0.15mm Prusament settings, with 15% gyroid infill...CAD ModelsI added the STEP and SOLIDWORKS...

Old School will likely require some servo extensions. Notes: Printed in eSun PLA+ Arrange parts on the build plate according to the illustrations. Cura: Support Touching Build Plate, Infill 15% Trim away the 2 little locking tabs inside the slots of...

Printed sets of restriction enzymes will be for sale on my etsy page. Steps! a. Build a model of DNA matching the restriction enzyme.<br/> b. Model how the restriction enzyme cuts the DNA along specific base pairs.<br/> c. Show where the sticky...

If the artefact had not already been collected by a previous player, the player whose token lands on the field collects it.Quick  tip: If you wish to make the game more educational add the following rule: Before collecting an artefact by stepping on...

The more precise(=time-consuming) the printing is, the greater this effect is. From photo to 3D modelHigh-contrast photos are suitable as motifs, which can be adapted somewhat for the further steps using an image editing program (e.g. Gimp). For the...

I have included a Binary and ASCII STL file as well as the step files so there is plenty of options for slicers and modification in cad software. Obviously its heavily inspired by the Briss Fang because I thought it was an elegant design and most...

See steps 14 and 15 in my original post for details.Use hot-glue to fix the cables and connections in place and to isolate the cables and connectors from one another.Check that the base part still fits. ...While the top part is facing down, add super...

Each turn, 6 dice are thrown.Steps by dice thrown:Advantage is a special part of the game. Players move their pieces around the board in clockwise order.&nbsp;<br><br>The first piece for each player can leave the home area <strong>using any...

The "base" self-aligns to the Lid and the screws will align the "underlay" to the "base". Assemble the TUSH parts and slide them onto the rails of the "base". Adjust the width of the TUSH rollers and place your spool of filament on the assembly, with...

It is easy to plane cut the meshes apart in Fusion 360 and is the next step to fit pieces onto print bed. ... based on my mirror array experimentation here: https://www.thingiverse.com/thing:5158449 and https://www.thingiverse.com/thing:5162096 ...

Watch Devin's video from Make Anything below to see how to print something like this with a single extruder. Bill of Materials 1x Wemos D1 mini is recommended, but any other ESP8266 variant should work too, but it might require an additional...

One of the first things I added to my Prusa i3 was a Raspberry Pi 3B+ running the excellent OctoPrint platform as this provides WiFi remote control and webcam monitoring of the print – a must for any 3d printer. However, I wanted a fully integrated...

... I apologize for being MIA. I have had some serious family stuff going on. I will not be able to make any changes to this for a little while. So I have uploaded the STEP file for anyone that would like to take a crack at making improvements.

Look through the following steps and try them in order until your problem is solved.If the AMS doesn't close, try printing cardboard_spool_ring-thinnerIf the edges of the cardboard spool are uneven or wobbly (as was reported by some users with...

The second goal of this build was to keep the possibility of converting back the coreYX to&nbsp;Ender 3 V2 and here we are.The benefits of CoreXY system is that your ender 3 v2 doesn’t have to move the heavy glass plate anymore, so by addressing this...

... the donate link here. I'd really appreciate it!&nbsp;&nbsp;Changelog:28/06/2021 - Release of the files and some documentation, more images and video about the assembly will be added soon.25/07/2021 - Added step files.&nbsp;&nbsp;&nbsp;&nbsp;&nbsp;

10% steps could be displayed with 2x1 bricks 6) How much space must be given for play and user adaptation ? So far, the answer is "a lot"... (after 4 weeks into this project) ### More information...

If you don't want to use screws, you could skip this step and cover up the holes with the "Screw_Cover". I haven't tried yet, but they should have a nice press fit (let me know otherwise). ####Glue#### * It isn't really neccecary to glue anything, I...

If you don't do this, the servo arm will move in the opposite direction you expect when you calibrate it (this may be fixed in a future firmware modification, but for simplicity's sake flipping the connector does work) Assembly steps for winder Fix...

Get a sheet of paper under nozzle, and do 0.1 steps, and level as you wish going down progressively, note the distance on your LCD screen. Once the nozzle is correct height for you, issue: M851 Z-xx.xx where xx.xx is the distance you noted ...

I removed the mechanism from the housing (from the front) for this step.Alternatively, modify the model to move the hole for the TRS jack; but I like it where it is.3. The hours unit</p><ul><li>Install the mounting bracket on the bottom side of the...

UPDATE: GreatScott!, a large electronics YT channel, has made an FPV build guide using this frame!&nbsp;Check it out here:&nbsp;UPDATE: I have added STEP files and a new back mount (V2) which has 2 extra holes on opposite sides on the main one, for...