fms rc 3d models

Tools required-Soldering iron-Heat shrink-LiPo Balance Charger (like the IMAX RC B3)WARNING WARNING WARNING WARNING WARNINGDo not charge a lipo battery in the original lead acid charger that was included with your device. You will burn your house...

If you find this build too complicated for your skill level, try the much simpler RC version below. The link to it is https://www.thingiverse.com/thing:3671892 ** Part 1 - Track ** Head over to https://www.thingiverse.com/thing:3112734 and print...

You will need: From Botkits: 2 high-torque drive motors at 780RPM and 1 Scorpion DESC motor From Fingertech Robotics: 2 powerful brushless ESC's with 20A capacity 2 Fingertech Inrunners for exceptional speed 2 strong belts rated at 150T 2 precision...

The coupler and bowden tube clamp are designed for a 2.2mm flex shaft used in RC boats and 4mm PTFE. I found a supplier that sells 1m flex shafts for $30 after shipping, and I ordered some for testing. You can also buy it in bulk on Alibaba if you...

You could basically use anything you want, like an RC-Remote or anything that can tell the ESC to spin the motor. Just for completion I added my Arduino code. I take no responsibility in it destroying something because it is slow. You can send it a...

This is an RC 'robotic' dinosaur in kit form, built on a skid-steered platform. The user controls the left and right claws, which rotate using slider switches, and fires the neck/head/jaws by cranking them into action. The jaws lunge and bite with...

The Antenna Mount is positioned at the rear of the quad, featuring a hole for the VTX antenna, two RX antennas (90 degree), and a space to accommodate an LED strip (Aurora RC, 25mm x 6 mm). It's complete, printed with PLA, with support only from the...

I used small thin washers with 4 screws designed for plastic threading from some old RC servos I had. Then slide the Nimble over the threaded rod and use 3mm nuts and washers to secure it. Do not over tighten, refer to the Nimble documentation. I...

List of electronics components: (1) 2S (or even 3S) lipo battery (1) ESP32 board (**38-pin version**) (1) 2.4GHz transmitter (with at least 7 channels, one of which is a dial wheel) (1) 2.4GHz receiver (7 channels) (6) MG996R/MG995 servo motors...

This proyect born as a attempt to create a rc plane with a good performance, predictable and gentle characteristics, resistant, easy to mantain- repair, like the real counterpart the noble Pilatus Turbo Porter. This airplane combine the foam...

This project was born out of a desire to create an RC plane with exceptional performance, predictability, and gentle handling characteristics, similar to the real Pilatus Turbo Porter. By combining foam's light weight, moderate resistance, fast...

This is a set of parts to mount a Caddx Air Unit and gimballed servos on the front of an RC plane via a removal sled. This allows reuse of the expensive camera system on multiple planes. https://youtu.be/-2Ksvu3-FmI ## Features - Sled that...

Fasten the other end of the springs to the little hole drilled in the bottom of Neck_Rear_Cover To connect the Neck_Lead_Screw_Drives to the Neck_U_Joint_Base I used M3 x 50mm threaded rods...

It's really zero trouble, I can export configurations on my phone and send them over instantly.Lots of quads: (and more all the time)Armattan Marmotte (special design variation)Armattan Chameleon (special design variation)AOS RC AOS 3.5 / AOS...

(as shown in the pics) The parts I used: Controller: FLF3_EVO_BRUSHED Flight Controller Built-in Flysky 6CH PPM Receiver For Eachine QX95 QX90 QX90C...

Everything else shouldn't matter too much, personally, I'm using: - 3x NTM 2830 propdrive (KV is probs ~1200 too, I'm using old models), I'm running it on 3S with 11x4 props I think, 4S with smaller props also works, just listen to your RC forums -...

http://www.instagram.com/quadframesuk/ ***Subscribe to our YouTube channel*** For Product Giveaways, design help, Design Videos, Build Videos, Product Reviews, tips, RC related guides, builds and FPV flights. http://www.youtube.com/c/QuadFramesUK ...

This is my spinner design for the 3DLabPrint Spitfire MkIX RC model aircraft. In my opinion, the spinner (and the propeller) plays an important part in the general scale appearance of a model, and for some reason, the spinner designs of 3DLabPrint...

https://paypal.me/BrianBrocken Check out my other designs: * UMC - Universal motion controller: https://www.thingiverse.com/thing:4245315 * 3D-printable Davinci catapult gift card: https://www.thingiverse.com/thing:4067668 * Arduino controlled...

As this model is in 1:10 scale, it is rc controllable and not a quick print!This is my second 1:10 scale “Lanz-Bulldog” tractor. Many parts are quite similar to my 1:10 scale “Eilbulldog” but I have optimized most of them. The interior is quite...

I do not have a Model Diesel Engine to fully test this in real life:- https://youtu.be/cluPJf9axIo?t=1020 The "Rubber Turner Clock Mainspring Big Shaft Model Diesel Engine Starter.stl" is for an RC plane starter insert 30mm x 36mm 20mm inner hole I...

Remixed the Dremel Rotary Sander V2 by OldGaf into a smaller version with fewer flaps to allow my weak no-brand rotary tool to be able to spin it up properly. It still uses the same attachment system, ie one of those...

https://www.amazon.com/VGEBY-Mounting-Electric-Brushless-Accessory/dp/B08KS28X8H/ref=sr_1_4?crid=19HURUA6LE2MM&keywords=brushless+motor+mount+rc&qid=1681641816&sprefix=brushless+motor+mount%2Caps%2C221&sr=8-4 - Insert for Battery mount and the ESC...

M3 x 10mm Allen ·12 ud M3 x 30mm Cabezal Cónico ·12 ud M3 rosca autoblocantes ·4 ud M3 roscas ·1 arandela M3 Electronics: x1 Arduino UNO:...

https://nl.aliexpress.com/item/3D-Printer-parts-for-Titan-Extruder-Fully-Kits-Titan-Extruder-for-1-75mm-3D-printer-extruder/32778467785.html?spm=2114.13010608.0.0.PpxZXk...

Feel free to take a look at my other designs: * UMC - Universal motion controller * 3D-printable Davinci catapult gift card * Arduino controlled photogrammetry 3D-scanner * Fully 3D-printable turntable * RC FPV tank rover * Fully 3D-printable...

V2 is compatible with V1*** 1st published print so be nice :-)I have a few other things that I have worked on for RC cars (traxxas maxx) and some odds and ends around the house, but this is the first to make it to all of you nice folks. I'm 3...

06.06.2022 - Uploaded a modified version of "senior_kodi_rc.ino". Now with the possibility to pause the movie. (changes are based on source code of http://makerangst.com/remote-receiver-for-kodi/5) The background for this project is that my...

https://www.robocarstore.com/products/hsp-94186-for-donkey-car This design was inspired by Tawn Kramer's Odomoter video titled "Odometer Install on an Exceed Magnet Rc Car" (https://www.youtube.com/watch?v=l0KUXxfalIQ). I'm using a hall sensor from...

If you would like to support this project Please scan the Paypal QR in the pictures, all doations are accepted - ALL LOGOS ARE USED WITH PERMISSION FROM RITEWING RC - Install Bulkhead : https://www.youtube.com/watch?v=lQeaaCqVfKs Install SMA Sidebays...