flysky receiver 3d models

Slim case for FlySky receiver, there are hols for bind and update and for diode. ...

I really like the Flysky X6B receiver as it's cheap light and can monitor battery voltage, the one thing that holds it back for me is that it lack pins to plug in servos and esc's so is a bit awkward for RC planes. ...So I've created this little case so...

I've started using small 4-channel FlySky FS2A receivers in lightweight plane projects. The goal is to have something protecting the PC board when attaching the receiver outside a plane, like a profile foamie. This design consists of three parts for...

This is a mounting plate for the FlySky X6B receiver. I used to simply attach the receiver PCB with 3M UHB tape, but I recently ran into a situation where I needed to remove the electronics from a model to perform some repairs. The tape did its job...

The Holder for Flysky FTr10 Receiver is a compact and lightweight accessory designed specifically to house the popular FTr10 receiver. To set it up, simply open the ports and secure the antennae in place. Weighing in at just 6 grams, this holder is...

This is a compelling scenario for the FlySky Fli14+, a cutting-edge device that's sure to make waves in its field.

I was eager to utilize an X6B receiver on an EzFly Trainer, but there is no space inside, so I came up with this box to provide some protection for the receiver. The base closely resembles one I published earlier. There are cut-outs in the sides...

6ch mount for FlySky receiver, with antenna bars.

FlySky X6B Remote Control System Transmitter Housing The housing of the FlySky X6B transmitter is a robust and durable unit designed to withstand the rigors of frequent use and harsh operating conditions. Its ergonomic design provides a comfortable...

Box for securing receiver with Cable tie to Model Base.

Box for securing receiver with Cable tie to Model Base.

The multi-copter model was created during the development process.

I love the FlySky i6X Receiver for its rock-solid reliability and impressive range, along with the option to have 14 channels and a critical RSSI channel when using modded firmware. However, in Planes sometimes it can be a challenge to find a good...

This is a sturdy mount/holder designed specifically for the Flysky iA10B receiver. It features a unique mounting position that enables users to secure their antenna wires at a precise 90° angle, utilizing cable ties and heatshrink tubing for a clean...

Mounting Bracket Enables Easy Installation of Flysky Fli14+ Receiver on Standard 30.5x30.5 Stack.

Mounting bracket for the Flysky Fli14+ receiver which allows it to be mounted neatly to the existing 30.5 x 30.5 stack.

If you require a FlySky Receiver FS-GR 3E for your building project,

Flysky FS-iA6 Receiver 4.0-6.5V/DC 2A 6 Channel 2.4 GHz ReceiverDimensional accuracy +/- 1mm

FLYSKY,6 TO 10 CHANNEL,RC RECEIVER

A Case for Protecting the FlySky/Turnigy X6B RC Receiver.\r\n\r\nOne of this receiver's features is its compact and "naked" design, but it leaves it vulnerable to damage in the harsh world of RC systems if not properly protected. ...Perhaps someone will...

This is a simple holder for a FS-iA6B Radio Receiver. The holder is 49 mm wide, 12 mm in height and 10 mm deep. ...The mounting holes are 39 mm apart and uses M3 or #4 screws.

This is a simple holder for a FS-iA6B Radio Receiver. The holder is 49 mm wide, 12 mm in height and 10 mm deep. ...The mounting holes are 39 mm apart and uses M3 or #4 screws.</p>

This compact cradle securely holds an FS-iA6B radio receiver. Measuring 49 mm in width, 12 mm in height, and 10 mm in depth, the cradle provides a snug fit for the device. ...Two mounting holes, spaced 39 mm apart, facilitate easy attachment using M3 or...

Needed a custom-made mount for my new quadcopter and decided to design one that could hold the Flysky receiver in addition to the antennas, all in one unit. It perfectly fits the FS-IA6 receiver and keeps the antennas angled at 90 degrees using...

... printed with a solid 100% infill due to its thin walls. Once complete, the receiver will fit snugly in place. Prioritize testing the bin before securing the lid firmly into position. ...For added durability, use a PLA material for maximum hardness.

A compact enclosure designed specifically to safeguard a miniature FlySky radio control receiver. ...Perfect for mounting on platforms featuring a 10 millimeter hole spacing, such as the Wild Thumper, and likely several other models.

It's always frustrating to deal with tangled messes of antenna wires while setting up various gadgets. ...To tackle this problem, a solution has been designed to make life easier.

This is a cradle for a Flysky compatible Fli4+ RC receiver that mounts two antenna wires using cable ties and heatshrink tubing. The cradle provides a snug fit around the bare PCB without transparent heatshrink. There are two types of lids...

People can now attach a custom-made receiver holder that utilizes compact zip ties for mounting purposes, along with an even thinner base plate for added stability. ...The antennas in these devices are carefully crafted to fit snugly within PTFE tubes...

I required a mount for my Flysky FS-IA6 radio receiver to be placed on my Immersion Vortex 285 and couldn't locate one that functioned. I utilized Questpact's Antenna Mount as inspiration and created my own in 123D Design. The antenna on the receiver...