flysky fs i6x battery mod with usb power bank by 3d models

Another portable power solution emerges, this one hailing from the world of RC vehicles. ...To bring it to life, you'll require a cigarette lighter USB charger and an XT60 connector.

The sturdy Mount is built to hold a 20 count 18650 battery pack securely in place, and its robust construction ensures that it will not bend or warp under even the heaviest loads. ...To attach this Mount firmly, simply use 2 screws with a length of at...

For Extremely Large Battery Storage System.

4 packs of lipo battery from an old laptop battery, working very well

IKEA SKADIS ring for battery charger.Requires 2 SKADIS Universal Hooks from this collection.

... on the go. ...Each port can deliver different voltage and current levels according to device requirements. To use this adapter, you'll need a USB Power Distribution Board that's available from online retailers like Amazon, Banggood, or Aliexpress.

The settings are dialed in to precision, with a minute adjustment of 0.2 millimeters to the layer height and an optimized infill density at 80%.

Power Bank for 18650 battery.

With FlySky FS-i6, I've always been frustrated by the fact that the remote control can't be normally placed on the table - the connector sticks out. I designed an adapter so that the cable runs parallel to the plane of the console. The FlySky cable...

... Alternatively, you could also use a velcro strap (up to 20mm wide). Just like the original concept, you can easily bend the switch protectors downward using a heat gun. This particular mount will also fit the Flysky FS-i6X and the Turnigy TGY-i6.

FlySky FS-I6S top-to-bottom and bottom TV stand for FPV applications requires securing with foam inserts to prevent TV movement.

Custom trigger mod for the Flysky FS-GT3B Transmitter to allow this transmitter and receiver to work with an airplane ESC. Doesn't require any irreversible mods to the stock controller and only takes about 10 minutes to change. The trigger adjusts...

I'm using a Flysky FS-CT6B transmitter with an 800 x 480 TFT color monitor. No screws are used, just the rail on the back of the monitor. Easy to assemble and disassemble for transport. Printed with Creality Ender 3 PLA at 20% infill. Results...

add - PD/QC3 charger with fuse - 2 6.3 terminal male - 4 screw (3x16) - IRF4905 - 100k resistor - zener diode (13v) print two parts: base and top /!\ there is no overdischarge protection on X20 battery add protection circuit (IRF4905 + zener +...

GoPro mount for FLYSKY FS-GT5 where you can connect different devices to record while driving your Crawler or radio control vehicle. Material: 2 screws m2,5x8mm 1 screw m5x45mm 1 nut m5 Installation: Remove the battery cover and attach the camera...

This is a phone/tablet mount specifically designed for the FlySky FS-i6S. To assemble this mount, you will need: * Two M8 bolts and nuts * One M5 bolt and nut * One M6 hex head screw I created this design to work seamlessly with the modular mounting...

Simple modification to the rear cap of a laser telescope collimator, included with many Newtonian models, enables it to function from an external USB powerbank. Built around the micro USB PCB, priced at $0.75 per pair on eBay, as shown in the image.

This is a Single Antena mount for Flysky FS-ia6B or Fs-ia style recever Print it in PLA or TPU For PLA put 103 or 105 flow

Specifically, I used: 1x Boost Buck Voltage LM2577S 2x LM2596 DC-DC converters - one for powering a fan and some lighting effects, and the other for providing 5-volt power to USB ports and two sockets. ...4x (2 red and 2 black) 4mm Banana Female Jack...

A 2 part bracket to hold a USB-C port for modding a SNES.

Neck Strap Balancer for FlySky FS-I6 or Turnigy TGy-I6, A Remix of Original Design Found on Thingiverse at http://www.thingiverse.com/thing:1748966

FlySky FS-X6B-V1.1, a 3D model of the 6-channel receiver, boasts four configurations:- Detailed with antenna- Detailed without antenna- Simplified with antenna- Simplified without antenna- Channel capabilities: six PWM channels and eight PPM...

this is a cover for flysky transmitters like the i6x or the i6. it's a remix for people like me that use these wider sticks on our transmitters. ...the print doesn't attach to the transmitter so you can use a bit of sticky stuff like blu tack (or other...

just added USB and orders plugs I have laying around RuiJC guild on who to build it is here:http://ruijc.webnode.com/products/got-a-3d-printer-then-you-can-easily-make-this-awesome-power-supply/ I didn't make just like that, sans I had some...

A Customized Power Hub Design for Modern Computing Needs This design is a modified version of the original project available on Thingiverse (https://www.thingiverse.com/thing:2076719), tailored to accommodate the demands of contemporary computing. In...

This creation was crafted entirely within Tinkercad's digital realm. ...You can now edit it directly on their website at https://www.tinkercad.com/things/kh8dKg5V5B6.

This 3D printed adapter connects a SMA connection to the Flysky FS i6. The RP-SMA female-to-UL connector used is available at http://www.banggood.com/RP-SMA-Female-To-U_FL-IPX-1_13-Pigtail-Cable-20cm-p-923077.html. No modifications are needed, and it...

This is an antenna modification for the Fsi6x that is suitable for the Fsi6 as well. ...With this design you will replace the stock antenna and you will not have to drill any holes in the radio. ... I printed as it is with supports and infill of 30%

... the CT6-B wastes an excessive amount of power using linear regulators. I replaced both 5-volt regulators with a switching regulator (a generic lm2596 ebay stepdown converter), resulting in significantly improved battery life (more than double).

https://www.thingiverse.com/thing:2467743/files I've modified the base to incorporate a USB C connector for powering the servos and, optionally, to power a camera board or anything else attached. The included file is for the base only. All...