flysky fs i6 phone mount by 3d models

We're looking for a camera mount that fits our needs perfectly, something designed specifically for the Nighthawk 280 Pro and compatible with the FatShark Pilot's camera or any other swivel-mounted cam. ...Tinkercad has just what we need - check out...

Flysky TH9x: https://www.banggood.com/Wholesale-FlySky-Upgrade-FS-TH9X-FS-TH9XB-2_4G-9CH-RC-Remote-Control-Transmitter-Mode-2-p-47904.html?p=DG23031123036201501P Made this to be simple, light and fast to print. Also going the GoPro Mount format so...

Flysky TH9x: https://www.banggood.com/Wholesale-FlySky-Upgrade-FS-TH9X-FS-TH9XB-2_4G-9CH-RC-Remote-Control-Transmitter-Mode-2-p-47904.html?p=DG23031123036201501P This mount was designed to be simple, light and fast to print. It's also based on the...

This uses the original part made by Prusa Research, but with a PTFE tube holder added under GPLv3. No fitting is needed; this design utilizes a conical hole to grab the PTFE tube securely. Adding the PTFE tube helps prevent the X-axis from yanking...

The design calls for a custom back plate specifically tailored to house the Martian II frame, allowing for seamless integration of the FPV system and antennas from a FlySky FS-IA6B (or comparable) receiver. This engineered setup enables an optimal...

The PCB slips neatly into place within the mount, secured by a zip tie. Antennas protruding from the rear can be tied up to the frame supports with ease. ...No need to apologize for the overgrown quad – this mount has been put through its paces during...

I revised the initial setup and now it looks much more suitable. However, I need to clarify that this configuration will only work properly if you're connected directly to Channel 1, which handles the output for the quad flight board. ...Additionally, I...

I designed a custom Flysky FS-IA6B receiver mount specifically for the Martian II quad frame. This mount fits snugly in the back of the quad between four rear standoffs, securing it firmly with a zip-tie. Additionally, I included standoffs for...

Customized version of https://www.thingiverse.com/thing:1148986 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1148986

Customized version of https://www.thingiverse.com/thing:1148986 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1148986

Human: Customized version of https://www.thingiverse.com/thing:813330 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=813330 Instructions Using the following options: case_taper = 3 pattern_overlap = 18 height_6 =...

Most FPV monitors have a 1/4-20 mount on the bottom, so you should be able to use these plates along with the aforementioned adapter and some threaded rod and nuts to mount an FPV monitor directly to your Flysky Noble NB4 radio. The plates are to be...

This is a protective battery sleeve for the Flysky Noble Nb4 with a GoPro style mount to make it easier to film while driving your rc's The camera mount is tilted a bit forward to prevent the GoPro cameras interfering with your fingers, my Sony...

Currently Working on an I6 Model.

This is a cradle for a Flysky compatible Fli4+ RC receiver that mounts two antenna wires using cable ties and heatshrink tubing. The cradle provides a snug fit around the bare PCB without transparent heatshrink. There are two types of lids...

This is a sturdy mount/holder designed specifically for the Flysky iA10B receiver. It features a unique mounting position that enables users to secure their antenna wires at a precise 90° angle, utilizing cable ties and heatshrink tubing for a clean...

I love the FlySky i6X Receiver for its rock-solid reliability and impressive range, along with the option to have 14 channels and a critical RSSI channel when using modded firmware. However, in Planes sometimes it can be a challenge to find a good...

Flysky FS-IA6B receiver mount for the Martian II quad frame securely attaches to the back of the quad between the four rear standoffs using a reliable zip-tie. To further expand my setup, I also installed 30x30 standoffs that allow me to add more...

The antenna holder is specifically designed for FlySky's iA6B receiver antenna. FPV enthusiasts can enjoy a 15-degree angle, but you're free to modify the source file if you'd like to adjust the angle to your liking. ... Get ready to take to the skies...

I took the gopro mount and added a trigger guard that attaches to the base of hte handle. The 2 halves are held together with 2m bolts and nuts. I suggest putting thin foam rubber in the upper part to give a more snug fit. Also included in the...

The FS-i6s display supports the addition of M3 screws for securing the linkages. ... Incorporate authentic screws to maintain the integrity of the radio.

This was a phone mount I created and it fits about any phone on the market and can even probably fit your phone case too! ...Fits a good selection of screws that could drill into a 2 by 4.

Here is a shell that allows you to swap out all the components of a Flysky fs-i6 radio, making it easier for kids to hold onto. ...All the trim buttons disappear and adding a 2S lipo with a Ubec 6V is done by: UBEC:...

This is cool phone holder

I held a cell phone in my hand.

Phone mount you can use to prop up your phone for scrolling!

A generic phone mount with screw attachment for universal mounting. By default this design comes with a mic stand adapter, and I'm working on a car adapter. The phone is attached to the adapter with a single M3 screw so the adapter should incorporate...

The case I had made was slightly flawed because its front grips were too small to securely hold the phone, and it was impossible to fit a charging cable inside due to the original's design constraints. Instead of modifying the STL file, I opted for a...