fluke 75 3d models

Case for adapter board for the optical port of fluke scopemeters. I have no schematics of the PCB, but it's just an IR Led + IR Phototransistor connected to a USB - UART converter. Screws to connect lid to bottom are M3 screws. ... A software for...

Replacement dial for Fluke 87V multimeter. The larger notch on the hex shaft is for a 006 O-ring to hold the dial in place, but I couldn't get the support out of that small area and the support worked equivalent to the O-ring. May be stronger...

the Fluke Microscanner 2So I re design a new one.   As a simple feedback for the work, thank you for liking and posting your making!I'm always happy to see your prints Happy printing !If you like my work and would like to support me, don't hesitate...

Clip-on stand for a Fluke 21 multimeter Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Rafts: No Supports: No Resolution: 0.2 Infill: 30% Category: Hand Tools

The hanger tab for this Fluke 17B+ features an extremely tight gap that may necessitate the use of a razor blade to open it up and allow flexibility. In comparison, the WFVN spring version boasts slightly larger dimensions, making it a better fit...

I'm replacing the faulty magnet end on my 17B+ Fluke meter holder with one that actually works right. Those weak and mislabeled magnets I got from Amazon were a total waste of time - even with a little rubber, they still kept sliding down. I'm...

This is a highly specialized replacement part designed specifically for the Fluke 8024A, one of the first digital multimeters ever produced. It should also be compatible with other Fluke meters in the same range, such as the 8020A, 8022A, etc. A...

A simple holder for a Fluke 87V or similar meter using the "rocking D" cutout on the back, combined with holders for meter probes. And because I often hurt myself, the probe holders have guards on top to prevent you from impaling your wrist when...

Simple stand to hold my Fluke 101 in a vertical position to save space on my work surface. ...I designed this to hold the meter while not in use so it's easy to remove and reseat with one hand.</p> <h3>Print Settings</h3> <p><strong>Printer...

I have printed the Fluke hanging tool by Thorius. http://www.thingiverse.com/thing:1086786 And I needed a way to hang the meter on a metal surface. So I created this little thing. You will need to buy 2 magnets ø25x7mm the kind i use is shielded...

The Fluke 362 Multimeter holder features a probe holder on its back and a cable loop on one side, ensuring easy access to readings with its angled design. Sitting at a 30-degree angle, this holder makes it simple to view the display. To protect the...

NOTE: &nbsp;Imported from Thingiverse without updates…This is a wall mount for a Fluke 114/115/116/117 multimeter. It will hold the meter with (or without) leads installed in the rear clips. It has two recessed screw holes for 3/16 tapcon concrete...

This is a battery cover for a fluke 111, I don't have the original piece nor screws so there will be some differences design wise, I printed it in PLA I don't think that material choice will affect function, there are multiple designs for the back...

This is a REMIX of the Multi-meter Stand (Fluke 112) - Thin (Joo Beng Koh) (2015) https://www.thingiverse.com/thing:1051560It had a couple of gaps in the STL model and after printing it at two different sizes, I realized it needed sides to keep my...

I've printed the Fluke hanging tool by Thorius - http://www.thingiverse.com/thing:1086786. To hang my meter on a metal surface, I needed something extra. That's when I created this little gadget. You'll have to buy two magnets with a diameter of...

This is a secure mount for a Fluke multimeter, capable of holding models 114/115/116/117 firmly in place. The unit can accommodate both meters with and without rear clips containing leads securely fastened into position. It features two strategically...

Fluke 116 117 replacement stand

Fluke Scopemeter 90 series top cover replacement

Fluke Accessory Mount for a 187 or 189 Multimeter

This is the switch shaft extension as used in the Fluke 341A and Fluke 343A DC Voltage Calibrators (and probably other items too) The original fluke extensions are quite fragile now so this replacement part will be very handy for some people, I made...

This is a remix of a box for Fluke 77 found there: https://www.thingiverse.com/thing:4010189. ... The Fluke 15B is tall than Fluke 77, so I extruded tehe top removing about 9mm of. ...

A nice and sturdy HSW mount for modern Fluke MultiMeters. ...Tested to fit both the Fluke 15B and 17B range of meters, but others like the Fluke 101, 106 and 107 should also fit.

I chose it for the yellow/orange color which looked close to Fluke yellow. Note that the stand won't work on any smooth surface, as it will slip. An easy solution is to cut a slit in some silicone tubing and put that over the end. I used...

Easy-to-install covers for the handlebar attachment of a Fluke 45 digital meter.

Simple tube replacement for Fluke VoltAlert 2AC Meant as an instertible .stl for further customization

Fluke 87 V pegboard holder. Print upside, with support. ... I used PLA with 60% infill.

Simple tube replacement for Fluke VoltAlert 2AC Meant as an instertible .stl for further customization Category: Hand Tools

The standard accessory stand included with the Fluke (and many multimeters) is not up to par, offering too much flexibility which often results in cluttered workspaces. In contrast, this designed stand provides a firm foundation angled at 45 degrees...

I combined two mounts for fluke multimeters to allow my 115 to mount to an Ikea Skadis pegboard. ...Uses the universal skadis hooks

Because i have not many place on my electronic desk, i decide to create a support for my Fluke multimeter on the top.