fluke 12b 3d models

Customized version of http://www.thingiverse.com/thing:537516 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=537516 Instructions Using the following options: holder_height = 65 holder_y_size = 60 strength_factor =...

I hope this holster can be useful for someone.

Finally cracked the code after multiple iterations to create a version that can withstand a 10-foot plus fall from a bucket truck without breaking, as well as normal rough handling. Investing in a CNC mill is now a must. Updated on September 16th,...

Rigid Desk-Use Stand & Upright Lead Holder for FLUKE 189 & 87-IV Portable Meters; snaps into back of Meter. Multiple versions. ...

This was made into a YouTube Video (link TBD) on my channel https://bit.ly/WhatAreWeFixingTodaysYT (whatarewefixingtoday).The Tinkercad file is here and is available in a one color file or as 2 stl's for a 2 color...

Individual parts may not match your connector (manufacturers may vary). ...However, the main external dimensions of the connector correspond to the drawing.SolidWorks 2012 and STEP AP214 models.

The E-12 Sky-Eye, a next-generation AWACS platform, was jointly developed by Earth Avionics (known for the VT-1 Supercat and VGF-14 Wildcat) and General Avionics (designer of the UAV-18 AI Drone). Intended to support Navy operations alongside new...

Sometimes you just need a gasket and you can't find the right material / thickness for your needs. In this instance, I needed a replacement fiber gasket that was approximately 1.5mm thick for a really old (well loved) Tanaka 1.2 HP outboard motor's...

A replacement rear foot for Pendulum's CNT-90 or CNT-91 frequency counters, which are also rebranded as the Tektronix FCA and MCA series counters and the Fluke PM6690. ... Attaches with a single M4x16mm bolt, and the original parts use a small washer...

I desgines this hook to work with the newer Fluke Multimeters that have a hard-plastic backcover that does not allow flex. Depending on application 2-4 parameters and 20% infill should suffice, print on the side for maximum strength. ...Don't forget...

Parts List NavePoint 3/4 Inch Roll Hook & Loop Reusable Cable Ties Wraps Straps Round Magnetic Base 2-5/8 Inch Ceramic 5 Magnet Nylon Body by National Hardware M5 x 40mm Flat Head 304 Stainless Steel Clevis Pins Fastener ...

Quick gag print for a colleague. ...Credit to "scorch" for the design

Stand by for instructions on Scopemeter 105B and similar units. You receive three interchangeable parts. If only one is broken, no need to print the whole set. All components are designed to work with the original model and can be used...

<p>Quick gag print for a colleague. ...Credit to "scorch" for the design</p> Category: Hand Tools

I had a lot of trouble with the original breaking when I tried to attach it to a mic stand pole. Every time I attempted it, it would shatter into pieces. So, I designed this one specifically to connect securely to a standard mic stand pole. I use the...

I researched the design of this wall mount, which was specifically created for a T110 Voltage Tester. I discovered that the T130 and T150 models should also work perfectly fine with it. However, please note that this mount is not compatible with the...

This design was crafted with precision using Tinkercad, a powerful digital tool that enables users to create and edit 3D models with ease. ...Make your own changes online at https://www.tinkercad.com/things/5S4310s4Kd.

replacement part for two-pole voltage tester. Tested only on model T130. Compatibility with attachment tips is not verified. If you want the same shape as the original, I will adjust the model for you (using a long screw without spring and fuse). ...

I was tired of my multimeter bouncing around inside my electrical toolbag. The bag has a hoop for a power tool, but it's too low for most power tools to hang on it. Fortunately, it happens to be the right height for the multimeter. Print it out,...

I started with the original and added an arm on the side to coral the cables. I usually have this hanging above my workbench and the side arm keeps the cables out of my way. It folds down to support the multimeter with the screen angled for easy...

Case is 271mm x 180.2mm on the print bed. I have added STL files that split the top and bottom in two parts and some joiners that can be printed so you can glue it all together for smaller printers. The top had a part next to the ribbon cable...

Workers should successfully install their system on a 2012-2015 Toyota Camry's oil filter housing and also any additional filter that matches in both size and flute quantity.

Busted the clip off my tick again... so here we are. The strength in the clip comes from printing the model laying down. I got away with no supports by dropping layer height to .1. ... Included in the model is a small 1mm x 2.88mm x .3mm piece that will...

A basic holder is suitable for any DMM with width

A model of the DIY Flukes hydrofoil from flukeskitesurfing.com

Customized version of https://www.thingiverse.com/thing:4737871 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4737871

Included the next models:F-6B; F-10B; F-12B; F-16B; F-18B

saab 9000, T3 flange for Mitsubishi TE05-12B, garrett TB0365 and volvo T3 turbocharger.update model/