flsun cube 3d models

The Mono Stabilization System requires a precisely crafted top component to securely hold the 608 ZZ Bearing in place.

Update 01/20/2020 - I haven't had this printer since mid-2018, I no longer develop it or have any ability to help with issues. FUTURE MODEL TO COME WITH HALF CIRCLE FAN DIRECTORS INSTEAD OF LINEAR FAN DIRECTORS. DISCLOSURE: The original design idea...

This is a sub-carriage that rides on X-Rods below the regular carriage that holds the hot end. The main advantage of using this part is that the carriage can be easily swapped out without disturbing the bearings or X-Rods. To assemble this part,...

I have carefully crafted this LCD TFT32 Case to function seamlessly without relying on the stock M4 Nut, opting instead for a sleek 20x20 aluminum profile. To secure the electronic board in place, you will require four M3 x 6mm nuts and four...

Human: I've created custom belt clamps for the Y-axis that perfectly replace the standard holder. Available in two sizes - one designed to fit neoprene belts with fiberglass cores and another tailored for PU (polyurethane) belts with steel mesh. Each...

**Note**: This design assumes you have either an E3D V6 clone or a V6 with their stock coolers installed, which it's designed to work seamlessly with. ...Leveling can be accomplished via the Z Limit switch and bed leveling screws if you choose not to...

You only need a few basic components: an M4 and an M3 screw, along with a switch. First, use the M4 set to attach this support to the printer's structure at a precise level. Next, place the M3 set above the switch to achieve fine calibration in the...

This part was designed to replace the original hotend fan support, allowing to place the fan turbine 5015, for layer cooling. Differently to others fan ducts, this one takes the air from the hotend rather than from outside. The main reason to make it...

Directing filament for anti tangle

I remixed it to utilize standard M4 nuts and screws I already had on hand. ...This bracket delivers a stiffer setup and simply has a more appealing appearance compared to what I'm currently employing.

2GT belt clamps for the Y-axis, Fits to replace the standard holder. In two sizes, one for neoprene with fiberglass core and for PU (polyurethane) with steel mesh. With opening for pushing out the M3 nut and for 2GT strap itself. With the size of...

This is a revised version for use with 40x10mm fans, specifically addressing an issue where custom support was omitted from one side, allowing the design to be printed directly without requiring additional support within the slicer.

I prefer mounting the sensor directly underneath the plate, which provides ample space for installing a part cooling fan.

Y-axis belt tensioner, as a replacement / enhancement for one of the Y-axis shafts. requires: 2x 2GT H-Wheel 20 Teeth for 6mm Belt Bearing 5mm Bore 2x M3 screw 30mm can also be a little shorter 2x M3 nuts 2x M5 hexagon screw 2x M5 nut (lock nut...

This part was designed using SolidWorks to replace the acrylic OEM Z micro switch arm with ease.\r\n\r\nThe main difference between this and the original is the use of M4 screws that securely attach it to the frame, unlike the single screw on the...

This is the critical component responsible for facilitating the replacement of the Y-axis system.

Y-axis belt tensioner, designed to replace or enhance one of the Y-axis shafts. requires: 2x 2GT H-Wheel 20 Teeth for 6mm Belt Bearing 5mm Bore 2x M3 screw 30mm, slightly shorter screws can also be used 2x M3 nut 2x M5 hexagon screw 2x M5 nut (lock...

2GT belt clamps for the Y-axis, Perfectly suited to replace the standard holder. Available in two sizes, one designed specifically for neoprene with a fiberglass core and another tailored for PU (polyurethane) with steel mesh. Featuring an opening...

Y-axis belt tensioner, as a replacement/enhancement for one of the Y-axis shafts. Requirements include: 2x 2GT H-Wheel 20 Teeth for 6mm Belt Bearing 5mm Bore 2x M3 screws, each measuring 30mm and can be slightly shorter 2x M3 nuts 2x M5 hexagon...

<body>This part was designed to replace the original hotend fan support, allowing to place the <a href="https://www.ebay.co.uk/itm/Fan-Turbine-5015-12v-Fan-50-x-50-x15-for-printer-3D-cooler-50mm-15mm-/332427605094">fan turbine 5015</a>, for layer...

In my case its a better solution to mount the Sensor under the plate, so i have more place for a part cooling fan

I designed a miniaturized version of the SKR v1.3 box, which I completed yesterday. The real magic happens when it's placed on top of the box. You can easily fit two standard MOSFET boards onto its surface. Additionally, there is a lid that securely...

This is the latest iteration of my modification, carefully crafted to ensure seamless automatic filament loading with minimal complications. To achieve this design, it's essential to procure a new small bearing 625. ... Original design:...

I added a new version with 40 mm. Check out the drawing - Orange = Aluminium profile. I'm really enjoying the cable chain from ELPO. I paired it with end caps from JimMurphy91 to create an adapter for my printer, which I printed using PETG. This is...

File to know the dimensions between the extruder and its fan to add any modification. ... * Only can be used as fixation the opposite part of the extruder of the fan

Newly modified to reduce height by 5mm for improved performance. Not yet printed or tested, but promising results are expected. The existing mounts for the Y belts lack adjustability and are about 12mm lower than where the belts come off the toothed...

I created custom cable management solutions for the 20x20 profile, incorporating 10cm strips to ensure a seamless fit. ...After redesigning and thoroughly testing them, I achieved a precise match that meets all requirements.

I was messing around with my Y-axis endstop during homing, but things took a turn for the worse when it suddenly slipped out of place. ...In a split second, I rushed to tighten it, only to have the entire acrylic bracket disintegrate into a million...

I Constructed This Replacement Because Mine Failed to Function Properly.

I wanted a small hotend because the original one was too long. That's why vibrations get transferred, resulting in a bad print quality. I measured it so that others can use this for other hotends, like the e3d v6 too. ... Have fun