flsun cube 3d models

... a more robust solution than https://www.thingiverse.com/thing:3744362. Find detailed information on http://www.ctheroux.com/flsun-cube-extruder-cable-strain-relief-holder-i2/. ...Source files are available upon request from the listed webpage.

Human: A replacement 2GT belt clamp for the X-axis, suitable for the standard plate of the Flsun Cube. This item is available in two versions - V1 and V2 - and also in older models without a square recess. When using belt clamps that don't have a...

PRINT SIZE: 290x290x340 (with BLTouch Sensor mounted) All screw needed for this build is basically from the Flsun cube printer with extra screws already used from the printer, so there's no need to buy a screw to build it. MATERIALS GT2 Closed...

A custom accessory plate is designed to enhance the FLSun Cube carriage modification, accommodating the standard E3DV5 hot end while integrating the original fan and sensor mounts seamlessly. ... Additionally, I have developed an adjustable mount for...

I acquired a FLSun Cube featuring a 4mm Z-axis inductive sensor located within the sensor area, necessitating the use of a 4mm thick glass plate on the worktable. As a result, the original inductive sensor fell outside the designated actuation zone,...

This is a 45mm Bushing Holder (LM8LUU) for the FLSun Cube, designed to replace the Y axis bushing and provide a more stable print at faster speeds. Two tie-wraps are required to secure it properly. Since I don't use an FLSun Hot End Carriage, I'm...

This is a 'cutup' version of "Better Y axis for flsun cube" with 47mm linear rod spacing - standard/original cube spacing, confirmed by my measurements. With this spacing, the original X carriage can be reused without modification. This project...

I designed this custom carriage for FLSun Cube to utilize a 50x15 cooling fan, paired with a Chimera nozzle configuration and standard inductive sensor. To assemble the Cable Harness Fixer, you will need two M3 nuts and two M3 screws measuring 10mm...

I overhauled this Vampire Carriage (based on original designs found at https://www.thingiverse.com/thing:2826072 and https://www.thingiverse.com/thing:2853986) in collaboration with Ben Myrdahl (https://www.thingiverse.com/Bmyrdahl/about) to...

This work is based on "FLSUN Cube X carriage restyling" (https://www.thingiverse.com/thing:2416730 by RafaelRS). Additional files need to be downloaded and printed from RafaelRS's parts, including 2x belt_mount. For the motor mount, visit...

Ich denke, du suchst nach Informationen zum Anbringen von Sensoren für deinen 3D-Drucker Flsun Cube. Hier sind einige allgemeine Schritte und Tipps, die dir helfen können: 1. **Wähle den richtigen Sensor**: Stelle sicher, dass du den richtigen...

**Firmware Update for FLSUN Cube Printer** Before attempting to flash this firmware on your printer, ensure that you are using the Ramps or MKS Gen L board with the stock drivers. This firmware is specifically designed for the Chimera version of the...

My Version of a Mount for an 18mm Autolevel Sensor, Like LJ18A3-8-Z / BX, for the Flsun Cube. Caution: I Have Not Verified Whether My Holder is Compatible with Standard or Other Belt Holders. The Small Version (S OS or S TS) Should Fit Both Dual...

This is my design for a carriage and limit for the Flsun cube printer. All complete files should print together. Also included is a remix of an X bearing holder you will need, which supports a part cooling fan and makes the overall print volume...

This holder was designed for the printer FLSUN Cube, but it could work for other printers with 2020 X section aluminium frame. You just need to screw the rod in the middle of the frame with M4 screws and nuts (like the printer ones); and the header...

Marlin 1.1.9 for the FLSUN Cube printer Before trying to flash this firmware on your printer please make sure you use the ramps or mks gen l board on this printer with the stock drivers. This firmware is meant for the chimera version of the flsun...

Marlin 1.1.9 for the FLSUN Cube printer Before trying to flash this firmware on your printer please make sure you use the ramps or mks gen l board on this printer with the stock drivers. This firmware is meant for the chimera version of the flsun...

Meine Version einer Halterung für einen 18mm Autolevel Sensor(wie LJ18A3-8-Z/BX) für den Flsun Cube. Achtung: Ich habe nicht überprüft ob der Halter mit dem Standard/andere(Außer meinen) Riemenhaltern kompatibel ist! Die Kleine Version(S OS oder...

I have taken down the entire XY train of my Flsun cube from 2020 V-Slot profile with pulley wheels, I designed new Y and X parts. I also remixed a design from Jon Schone for use with this overhauled system. The hotend hotswap system he designed for...

Make sure to keep extruder cables out of the way of the printing area at all times.

The design features mounting holes that can be used to attach a MOSFET board for the heated bed as well as a voltage regulator board for powering accessories such as lights. ...Additionally, two 9mm holes are provided for installing optional barrel...

Update: I've just upgraded my firmware, and discovered that the auto level sends the head too far to the right on my build, resulting in a head crash since the sensor never triggers. If you use this design, make sure it's only for z stop switch...

I replaced the faulty inductive sensor with a reliable servo motor that operates seamlessly every time. This upgrade eliminated any issues I experienced earlier. ...The replacement part can be sourced from Thingiverse, specifically from this model:...

This project was created using Tinkercad, a free online platform for 3D design. You can edit it directly on the website: https://www.tinkercad.com/things/aN51bt2YWz6 When my original model broke, I opted to print combi_hu's modified version of the...

I've been noticing my frame is moving a bit too much, so I came up with an idea to stabilize it - these parts are a perfect fit and keep your Y rods firmly in place. I've tested them thoroughly, so you can use them at your own risk. Enjoy! LIKE if...

I've been using https://www.thingiverse.com/thing:2496831 as a leveler and while it's been super helpful, I discovered that turning it could be a bit tricky. ...To solve this problem, I modified the knob by increasing its diameter and adding a pattern...

Human: Endstop Mount and Screw Regulated Bed Mount System.

We've extended the length to 100mm because the original version was only 80mm.

Human-readable STL file version.