flow rate calculator 3d models

At any rate, we were able to come up with a hotend housing that fit the Neo back plate perfectly, but also added some extra features over the stock housing. This design maintains the original CRT mount position and does not require any modification...

Since a standard 43x43x39 NEMA 17 extruder motor is heavy, it's best to print this in PETG or ABS since their rate of creep is much less than PLA. This will minimize deformation that may happen slowly over time that you may not notice.</p> <p>As with...

(Re)start CuraSample Marlin Configurations ============================The following sample configurations are from my Marlin 2.0 Bugfix - Firmware for Anycubic Kossel Delta Plus.Depending on your printer, Park Point, Feed Rates, Load and Unload...

High precision bed with upgraded heater An attempt was made to keep the moving mass of the extruder as low as possible, to increase the heating rate of the nozzle in order to enable higher speeds. I used the StepDown modules so that the larger fans...

Alibaba link for IP67-rated membranes / Specific Alibaba link (SV-021)Super glue: Gorilla Super Glue Gel worked great for me, as the applicator tip made it easy to get to the deeper bottom surface of the main body of the case. <a...

Other than the sleek design, it has many other benefits:It lowers the selector failure rate to less than 5% (0% to 2% in my tests).A mechanical “door” that controls the filament inside the sensor, not allowing it to get into the PINDA ball channel.It...

At the then-current exchange rate, the price was $10.50 USD.)My build is chronicled on the V1 Engineering Forum, here.I made several changes in my approach, some purely for innovation and some were innovations to save money.1. &nbsp;Instead of having...

So, when the shaft is spun it causes the clamps to advance in opposite directions and at the same rate. This mechanism means that your workpiece is always dead center in the vice, and no matter the position of the clamps the vice takes up the same...

 Print file includes:24cm LED strip (8mm) holders with end adapter, venting, 3 screw holes, and lens interfaceLight Mount connectors (connects light mount strips together)Wire Rack interface hooksOptional end cap for cleaner lookPrintable lens...

I imagine any short USB-C extension cable that is rated to carry video and power will work for the "pigtail" but am personally using [this cable](https://www.amazon.com/gp/product/B07YP4SGZT/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1) from...

The two versions of the cover need to be printed in TPU or other flexible material with a Shore Hardness rating of 95A (or close too it). The covers need to be flexible enough for the retaining flanges to be maneuvered through the cut in the bumper...

... more premium assets fitting various specific design or architectural goals at a moment's notice. In order provide constructive feedback & show appreciation - feel free kindly leave an honest rating following your acquisition experience here today!

So give me likes, post makes, comment and rate the print to show others and me how well it goes.If you post a make, let me know which filament you use.If you want to support me by donating a coffee go to https://ko-fi.com/antimaterie I would really...

 The next criteria I had a lever travel of between 110 - 120 degrees with each pull, which necessitates a spring with a compression angle of at least 110 - 120 degrees.The hardest part was finding a readily available spring that has sufficient torque...

The printed structure could be accomplished with one or multiple rovers working in unison and alignment markers on three or four corners along with their rate sensors and accelerometers for precision building. As the rover lays each layer, only...

You can skip the speed controller and keep it at 120V and 27,000 and mill soft metals at slow feed rates with 1 or 2 flute. Although the cheap 3-5$ speed controllers should work fine for 2.4amp motor. I do like that this motor is lighter and...

Alibaba link for IP67-rated membranes Specific Alibaba link (SV-021) O-ring: 44mm ID, 48mm OD, 2mm width. Go for 70A hardness. 50A is a bit too soft. Purchase at a well-stocked Ace or Amazon:<br/> <a...

=> set your user and that should be it for this part ;0) ----------------------------------------------------------------------------------------------- Klipper ---------- From a terminal(or Putty), connect to your Raspberry Pi then: - Connect your...

The motors are rated at 30 RPM at 6 Volts.The drone/robot was printed on an Ender 2 and a FolgerTech 2020.The 3D printed parts needed from RobotHuts design are:footclip 2latch 1bodyBack 1 / the door will be replacedfoot 2leg 2bodyFront 1The motor...

We stand out by striving daily for top tier realism found within digital creations, always bringing more precision every time you click and download something that represents a part of your next world – it would truly be wonderful to rate highly this...

This remote includes an internal 12 volt battery rated at 1 year of operation and a single red LED to indicate remote control activity.LED Benefits: Unlike gas burning and arc type lamps that have glass bulbs, LEDs have no filaments or fragile...

* the cog shape profile, * the number of outer ring teeth, * the number of sun teeth, (the ratio between ring and sun teeth will affect torque) * the number of planets * the gear height (either side of the pipe channel) * the pipe outer diameter *...

Usually you get a copy not the original one from Tower Pro.&nbsp;But they work (sigh)2 brushless ESC power regulators (30A will do)1 RC command + receiver (I used a Flysky FS-T6 6CH and the R6-B receiver)My 2 cents on motors: They are rated in turns...

Feed rate changes the speed of the motors. Be careful to not move the azimuth axis too far so the stepper motor wire connected to the motor for the altitude axis doesn't get wrapped up and pull. I found the following information about GRBL...

In fact, the output of the power supply to the battery should be switched so that a diode is not needed to keep the fans and power supply from draining the battery when not charging. The power supply is a 5V-30V wide input voltage variable output...

Their international shipping to NZ is crazy high (USPS Flat Rate International - US$80), so I had them deliver it to a freight-forwarder instead.Printing instructionsPrint the adapter that'll attach to your lens' foot with the following...

This mod allows you to power the electronics from a low-rated UPS, while power to the heatbed is supplied direct (not via a UPS). The bed should hold temperature adequately if left without power for a few seconds.To Do - Klipper IntegrationIdeally...

My build on Rotorbuilds for my full parts list: https://rotorbuilds.com/build/27266 Video on the frame design: https://youtu.be/CI2ykUmTqy4 Flight Footage: https://youtu.be/bSuooiEz3OQ Recommended parts: Flight Controller and ESC - [DarwinFPV F411...

This lamp is T6 rated and ideal for hazardous locations where UV lamps are used to cure coatings and adhesives or as germicidal agents.***PLEASE NOTE: ANY FREE SHIPPING OFFERS DO NOT APPLY TO THIS HAZARDOUS LOCATION LIGHT FIXTURE***The EPL-48-4L-UV...

If you are using a Prusa Printer, there is an example project for PrusaSlicer ("LR2180-ST-M Print.3mf").Print the template with PLA (or PETG).Select 0.2mm layer height.Use the quality setting.Print with 3 perimeters to get better rigidity (especially...