flipsky dual vesc 6 6 3d models

Hello, I designed this crankcase for a vesc 6.6 plus on a GTR Carbon evolve deck. I add the power button on the crankcase. ...I've already tried to print it on a FDM ultimaker and it works perfectly.

Hello, I designed this crankcase for a vesc 6.6 plus on a GTR Carbon evolve deck. I add the power button on the crankcase. ...I've already tried to print it on a FDM ultimaker and it works perfectly

Electronic speed controller assembly 3D model. ...Vesc 4.20 from Flipsky.Dimensions accurate up to 0.1mm (+- 0.05)

Electronic speed controller assembly 3D model. ...Vesc 4.20 from Flipsky.Dimensions accurate up to 0.1mm (+- 0.05)

Dual VESC System Plus Receiver Enclosure Designed Specifically for DIY Electric Skateboard Enthusiasts, Perfectly Compatible with the Concave Shape of the Loaded Vanguard.

My take on a dual VESC enclosure is designed specifically for an electric skateboard. It features M3 sized mounting studs with ample space within the case for wiring and a designated spot to secure a receiver via zip-tie. The mounting holes are...

A solid base for two VESCs, each paired with heat sinks and three capacitors to keep them running smoothly.

For more information on the VESC open-source ESC, please visit vedder.se/2015/01/vesc-open-source-esc/. The specific heatsink used in this project can be found at...

This is a WIP for ennoid vesc, newly added lips for better alignment, however so far untested and unfitted, so do not take this as a final version just yet!

It features dual FSESC6.6 Based upon VESC6 with an Aluminum Heatsink. A generous gap of 14mm allows for the secure fitting of UART and RX connections under the VESC6 controller. ... To assemble this case, you will need: M5 x 15mm screws (six in total)

Dual VESC mount setup requires precise modification to integrate properly with a high-capacity capacitor.

Dual VESC Enclosure for Vanguard Skateboard Deck Seal the deal with a TPU print. The model breaks into two halves, making it a breeze to print. Printed in ABS at 100% infill, with acetone glue holding everything together. ... Keep water and debris out...

Dual Accucell 6 Case Redesign, a creative twist on the original holder.

A versatile 6-Sided Die designed specifically for printing with a Dual Extrusion Setup.

My FT-6 was having a Z axis skipping issue when Zhop was on so I switched to dual Z axis motors, updated the firmware to use E1 driver for the second Z motor. All is well now. Here are the tools I used. The clamp is for the bed so you don't have to...

Case compatible with both large and small-sized iPhones 6 Plus phones.

This is a cooling fan adapter designed specifically for the Folgertech FT-6 dual extruder option. For larger diameter nozzles, adequate cooling becomes an immediate necessity. This solution employs two standard 5015 blower fans (I used Winsinn ones...

Docking station for iPhone 6 and 6S models or iPhone 5 and 5S models. Rear slot supports charging, front slot holds the device in a standing position. ... Printer Details Brand: RepRap Model: BCN3D+ Features: Rafts: Not Required Supports: Yes Print...

Bauteilkühlung für den ENDER6 Dual 5015 Blower aufgenommen an dem Original 4010 Bauteilkühler Platz. ... Airguides L+R sind Mittig zu dem Blower Tunnel Airguides L+R V2 sind mittig zur Düse angeordnet

I was inspired by the Updated Overhead Filament Spool Holder remixed by Dereksunday, which I used until recently when I upgraded to dual extruders. Since I have the PrintedSolid safety enclosure and didn't want to modify the top panel to accommodate...

Dual iPhone Dock Station for Lightning iPhones. The dock features a rear charging port and a front slot that allows the device to stand upright while it's being charged. ...Print SettingsPrinter Brand is RepRap, Printer Model is BCN3D+, Rafting is not...

6

6

Customized version of https://www.thingiverse.com/thing:1688868 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1688868

This enclosure is specifically designed for Flipsky's FSESC 6.6 Mini size mountainboard trucks. I've made sure there's enough space to attach the heatsink to the cover, providing some passive cooling. Additionally, I've included room for an antispark...

http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: font_size = 42 line1 = 6 minimal_color_layer_thickness = 0.6 bar_style = bar_only lug_text_distance = -10 borderextruder = extruder2...

http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the Following Options: hole_radius is set to 2 flat_bottom is enabled at default value stick_thickness is now 3 units font_size remains unchanged at 10 message length...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=50437 Instructions Using the following settings: Block Length is 1 unit long Block Width is set to 6 units wide Block Height measures a height of 1 unit

Human: Customized Version of Thing #475250 from Thingiverse.com Created with the Thingiverse Customizer at thingiverse.com/apps/customizer/run?thing_id=475250 Instructions for Printing: Choose from Predefined Options: Font size (f) set to 75 units...

http://www.thingiverse.com/apps/customizer/run?thing_id=53451 Instructions Using the following settings: number of teeth on planets is set at 15 planet twist setting stands at 2 points tolerance level has been set to a minimum of 0.4 inches diameter...