flipper zero 3d models

The only other TPU case for flipper zero did not cut it for me, so had to create my own.I would recommend printing this in softest TPU possible, as it might be a bit hard to put it on the flipper. historyv1 initial releasev2 wider cutout in...

The base (**bottom**, **top** and **clip** parts) are from [this model](https://www.printables.com/model/215066-flipper-zero-case-without-overhangs), which is a remix of [this model](https://www.printables.com/model/204882-flipper-zero-case), which...

Case-cover for IR Blaster, Flipper Zero.

Usage for the Flipper Zero Case by Kermit (https://www.printables.com/de/model/256570-flipper-zero-case). The insert is suitable for the Flipper Zero with a silicone protective cover. The silicone protective cover should not be thicker than 2mm. I...

... it with actual pictures and any final tweaks to the design. Extra Hardware: 2 - 2M x 20 mm Cap Screws 2 - 2M x 3 x 3.2 mm Threaded Inserts Flipper Zero Module: https://www.tindie.com/products/rek5lab/flipper-zero-marauder-esp32-cc1101-nrf24l01/

Full case structured in 2 pieces (base and top), for ESP32 WROOM modules, designed specifically for Flipper Zero via GPIO connection.

This is a simple case or cover for the [Flipper prototyping board ("ProtoBoard")](https://shop.flipperzero.one/collections/flipper-zero-accessories/products/proto-boards) with 10mm of clearance on the "top" and 5mm of clearance on the "bottom." I...

Case for the board Flipper zero WIFI. Made it as small as possible. The structure is printed without supports. 1*5 screws are used to fasten the top part. ...Now I'm working on protection for contacts.

A case for Flipper Zero NRF24 module from aliexpressOne version with nuts and screws and another only with swrewsNeed 4 m3x10 screws for no nuts versionNeed 4 m3x12 screws for nuts version

Remix of J03's Hard Case for the Flipper ZeroAdded Magnets for closingRequired hardware:2x M2.5 x 10mm screw2x 6mm x 3mm Magnets 

... the boot and reset buttons. Hardware used. (purchased at my local Ace hardware) 4 M1 Flathead screws 4 M1 Nuts This is a remix of WingedFuse Model over at https://www.printables.com/model/348239-case-for-flipper-zero-wi-fi-module-with-ruthex-thr

Flipper Hard Case V2 of.stl is a open face case for a Flipper Zero to access the screen, buttons, USB, IR transmitter and GPIO pins.Flipper Hard Case V2.stl is a full hard caseThis version does not require hardware as it uses folding the plastic as...

Flipper Hard Case V2 of.stl is a open face case for a Flipper Zero to access the screen, buttons, USB, IR transmitter and GPIO pins.Flipper Hard Case V2.stl is a full hard caseThis version does not require hardware as it uses folding the plastic as...

Bill of Materials (excluding print) --------------------- - 1x ESP32 "D1 mini" - 1x 2.54 header pins (1x10) - 1x Experiment PCB (cut to size) - 4x Wires - 4x Threaded brass inserts (M2) - 4x M2x4mm Before attaching your ESP32 to Flipper Zero you...

Printed the Flipper Zero Case ©by Shutdown but I wanted to put other stickers on the lid, so I decided to remove the indentations for the flipper letteringFYI:I used some M2 bolds for the lid and some M3 bolds for the clips

This is a simple snap around case for the Flipper Zero, with a belt clip already attached. I got this from another listing, but I decided to go ahead and combine the belt clip with the case itself, vs gluing them. ... I am going on vacation and want my...

The thickness of the bumper is 2mmIt was made with a very soft TPU  due to the wrapping surface of the case and the difficulty of inserting Flipper Zero.https://endimadesigner.etsy.com/ Changelog: 09/23/2022Cover type "D" added with the following...

Flipper Hard Case V2 of.stl is a open face case for a Flipper Zero to access the screen, buttons, USB, IR transmitter and GPIO pins. Flipper Hard Case V2.stl is a full hard case This version does not require hardware as it uses folding the plastic...

... [my previous case/cover](https://www.thingiverse.com/thing:5411771). ... I needed a simple, mostly-closed cover for my prototype CO2 monitor module for the Flipper Zero. The case comes together with M3 heat-set inserts and 20mm long M3 bolts. ...

This is a simple model of the flipper zero wifi dev board. I know it isn't the best quality, but the measurements should be accurate enough for you to use it to make your own case for the dev board. I got the measurements using a caliper and I...

... settings need tweaking to fix the stringing on the hinge rings.</p><p>I didn't add the text to the top cover, and kept the single-layer spacing. If you want the 2-tone look, check the original Flipper Zero Case for the YouTube video and text STL.

Originally was in 4 pieces but I managed to get it down to 2.I recommend:Set GPIO pins in flipper zero and hook them up to antenna per instructions (make sure to test it before affixing to case)Affix pins (however you choose) to bottom bracket of...

... are atrocious but I am reasonably pleased with how it turned out. Included is 2 versions, one for flippers with a silicone case, and one for flippers without a case. ...Many thanks for the commenters below for figuring out the proper scaling!

I designed this for my wife's Honda, and I think that it works great! ...Enjoy your flipper on the go!

...The hole in the lower part is supposed to fit the flipper with the original packaging's sponge, but it doesn't fit because I bought the silicone bumper, so you will need to print 'Alrederdor Flipper' so it doesn't go around the box and doesn't move.

This a remix and modification of Ric Tru's Remix of yanev's design https://www.printables.com/prints/39729-tool-box-parametric I have reinforced the stubs and expanded the box to fit both flipper, WiFi dev board and some extra room for additional...

... in Prusament Galaxy black. It now can fit not only the flipper, but also the wifi dev board! Also, there isn't really anything holding the board itself, so get creative! Just needed this one quick. ...Ill do an updated version in the next few days.

I converted some of the flipper logos to stl so I could embed them in my prints. Put your MMU to work. :D</p><p>The backing is so that each “pixel” doesn't become its own model. ...I made the backing .01mm thick, so the slicer should ignore it.</p>

This is a flexible case I designed for my Fipper Zero a while back, I thought I'd clean it up a bit and publish it here. ...Enjoy!

Flipper Zero holder for Ikea SKÅDIS Pegboard