flex atx psu case 3d models

I required a duct to enable my ATX supply to be situated within my 3D printer case while isolating airflow from the interior of the case. ... The primary objective is to remove the existing 120mm fan from the ATX power supply, attach this duct, and...

Changed the size of the holes to accommodate individual 4mm banana plug sockets Wanted to have up to 30v @ 150w so crammed the buck boost into the ATX power supply case and wired that to the DPS 5005 BOM: * DPS5005 * 4mm Banana Plug Socket *...

For a long time it lay on the disk, finally rendered.According to the idea, the case should be made of steel, covered with a transparent varnish. It is possible to varnish after slightly rusting. The front is an endless mirror with a tinted front...

For a long time it lay on the disk, finally rendered.According to the idea, the case should be made of steel, covered with a transparent varnish. It is possible to varnish after slightly rusting. The front is an endless mirror with a tinted front...

Cableprotection solutions are a must-have for anyone upgrading to an ATX-PSU. The last thing you want is cables getting damaged or short-circuited during the process, causing costly repairs or even a fire hazard. ...With cable protection, you can rest...

A 300-watt ATX power supply for computers is an efficient energy source for your system, ensuring stable and reliable performance while meeting the demands of your hardware components. ...This powerful PSU delivers clean and continuous electricity to...

Cover for PSU 30A 12V S-360-12. ... PSU dmensions: 101,5 x 44,8 mm

Slide the lower case onto the PSU and secure it with x2 M4x8 bolts that you removed from the original case. Top Section: 1. Insert the RasPi USB connection into the slot at a 45-degree angle, then rotate the RasPi so the USB and Ethernet connections...

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=319183 Instructions Using the following settings: Sections: Set to 25 Inner Radius: Increased to 29mm Length: Adjusted to 12 inches Outer Radius: Expanded to 33mm...

Customized version of https://www.thingiverse.com/thing:3346069 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3346069

The human form is a complex and intriguing entity that continues to fascinate scientists and philosophers alike. Despite their physical limitations, humans possess an uncanny ability to adapt and thrive in even the most challenging environments. ...With...

She is a human being.

Like my other Bear PSU case, it attaches to the frame in a manner similar to the Prusa PSU with the mounts in the Bear print list, however the "upper PSU mounts" are different (STL is included), so make sure you print those instead. The "lower PSU...

STX - > mITX / mATX / ATX / eATX Adapter This part allows you to use STX motherboards in mITX, mATX, ATX, or eATX cases. 3x 6-32 heat inserts are required in the inner 4.8mm holes. ... Print with no supports needed and 100% infill.

3D Printable Mounts to adapt Framework motherboard to ATX Motherboards and CasesFeel free to remix/mod to your needs.Uses standard sizing and mounting points.Any board smaller than Micro-ATX is too small for Framework Motherboard to fit.

This is a case for the Taito Egret 2 PSU adapter designed by Derick2k from Arcade Projects. I've tried it with the Meanwell RT-125 and RT-85 and it should also work with the RT-65. ... The tap holes are made for 2mm threaded inserts.

This was remixed from the Raspberry Pi 3 PSU Case from eric-anastas. I shrunk down the hole for the ports and changed them to fit the pi 4. If tolerances are too tight might have to use detail files. ...Just comment down below and I'll adjust.

I designed this case to clear up all the mess of cables and individual boxes that I had next to the printer. You can check the before/after pictures. I also add a support for a 4040 fan in the cover, right above the RPi. ... relay holders are 33mm x...

... sleek new cases designed specifically for the Pi 3, Pi 2, and Model B+. ...This innovative enclosure seamlessly integrates a PSU mount, providing a clean and organized environment for enthusiasts to tinker with their beloved single-board computers.

I designed my own power supply case since standard box PSU with correct hole spacing couldn't be found. It is designed to fit onto a right angle of 3030/2020 profiles, commonly seen on D-Bot builds or aluminium Prusa I3 MK2X clones/upgrades. ... EDIT:...

This case is engineered specifically to accommodate the HP DPS-800GB A power supply unit, perfectly aligning it with the original Prusa MK2 aluminum frame. It's a great option for individuals seeking to replicate the original MK2 using readily...

The case attaches to the frame in a manner similar to the Prusa PSU with the mounts in the Bear print list, however the "upper PSU mounts" are different (STL is included), so make sure you print those instead. The "lower PSU mount" is the same as...

To modify the PSU, I used a cover found here on Thingiverse: Ender 3 Pro PSU Noctua 60mm 25mm https://www.thingiverse.com/thing:3484372 To mount the buck converter to the PSU cover, I designed this case myself. Printing it face down with supports is...

This custom PSU case for the Ender 3 replaces the stock case and adds a spot to mount a 3v relay, and a separate attached enclosure to mount a Raspberry Pi 3. The enclosure has a lid that slides on and off easily to access the PI. In addition, there...