flex atx case 3d models

Computer motherboard ATX size

... IMPORTANT NOTE: Fits ATX power supply with depth 125mm or less. ----------------------------------------------------------------------------------------------- I printed the case in black PLA, but PETG will also work well (probably the best option)

The redesigned case now accommodates an RPi3, an ATX power supply, two TL-Smoother plus units, a relay for LED lighting control, a MOSFET module, and a 120mm fan. This setup enables continuous operation of the RPi (running OctoPrint) thanks to the...

In my case, I use an ATX power supply in one of my projects, so it's very convenient to have the electronics nearby. I chose one of the chasses that I like best and decided to make this remix by adding a bridge with holes matching the screws of the...

I'd like to make some remixes to accomodate more form factors in the future (ATX, mATX motherboards, SFX power supplies, etc.). Feel free to remix, I'd love to see some custom remixes to fit your components! ... Post in the comments if you need help...

Here is a printable 3D model that seems to fit hard drives into the [Logisys CS859SL/CS859BK XBlade](https://www.game-debate.com/cases/index.php?ca_id=1489&cases=CS859SL%20XBlade%20Silver) Full sized ATX case (not sure why some sites claim this is...

I employed Autodesk Inventor to design the component that houses the base plate, I/O panel, and where the graphics cards are secured. ...The measurements are completely accurate for use in modification projects.

Powering up your gear requires a strong connection from the computer to the wall outlet via a reliable fastener.

I was thoroughly impressed by james_III's design, specifically the Lab ATX Power Supply Skeleton Case. However, one detail kept bothering me - the handle. So I decided to take matters into my own hands and fired up my brand new freecad 0.17RC (time...

There are two end caps that fit snugly over the ends to secure the whole thing in place.Note: This was tested for fit with the HCDC 24/20-pin ATX DC Power Supply Breakout Board Module and the Electronics-Salon 24/20-pin ATX DC Power Supply Breakout...

If you have an old ATX computer case and power supply lying around, why not use it to expand the storage of your main PC? Turn it into a DAS! (Direct-Attached Storage) This design mounts 4 disk racks in the space that would normally be occupied by...

Holder to place an ATX power under the table.

I built this project to breathe new life into an old computer, pairing the Intel Atom N450 processor with a standard ATX font and 3.5" HD HDD. Since the Atom N450 doesn't require a cooler, heat won't be a concern. I designed two projects: one open...

Remixed https://www.thingiverse.com/thing:4916230 to include a 3x2 cutout for GPIO pins 13-18 which include 3.3v and GND as well as 4 GPIO pins used to send ATX reset and power commands and read the status of HDD and Power LEDs. See...

A simple frame with pins to drop in a micro ATX mainboard. PSU mount in the bottom and 2,5" or 3,5" HDD / SSD mount on the side. Tolerances of 0,1mm are built in. Stick the parts together and some superglue in the ends. The second shortest beam is...

The ATX power supply unit is designed according to the industry standard for ATX PSUs, featuring a 120 x 120 x 25mm 7-blade fan for efficient cooling.

The holder will position an ATX power supply unit beneath the table.

Video embedded below showcases this standard ATX PSU stack: https://youtu.be/2Qe3c4gW5tY

This is a case for theATX Board PIKVM Remote Control ATXA-A+ATXA-B Board for Raspberry Pi CM4as found on ebay -> https://www.ebay.de/itm/354162821153

I wanted to make the smallest case for my new router/firewall which is basically a computer with lots of ethernet ports and a wifi card. I also wanted to integrate a small switch in the case and the power supply would be a picoPSU with external...

Here is a 20 and 24 pin ATX Male connector housing. ... It's designed to be used with 5559 ATX crimp pins. ... You need to ground the PS_ON (pin 16) to turn the PSU on.

ATX connectors are commonly used in power supplies for computers, providing efficient electrical connections and compatibility with various motherboard types.

TLDR; **Print the corrected support bar to get one that actually fits the original model** 2x support_bar_lenght_corrected.stl **Only print the following if looking for 5.25 inch bay support:** support_bar_5-25-bay-left.stl...

One has keychain. ...Enjoy

For those looking for defense but lighter loads. Clever move - just draw the parasolid and then add text that's a quarter inch thick, curved and easily readable at 0.6 inches in Arial font size is preferred. Add custom text next and permit it to...

This versatile, form-hugging enclosure perfectly complements the sleek design of the DaVinci Miqro. ...If you're a fan of this model, be sure to give it a well-deserved five-star rating and spread the word by sharing your thoughts with others.

Whistler's revolutionary TRX-1 ruggedized enclosure delivers top-notch protection while preserving flexibility.

<p>Tiskuto na výšku vrstvy 0,35mm z PLA. Hlavně kvůli rychlosti tisku. Podpory nejsou potřeba. Jsou součástí modelu. K sestavení stačí 12x šroubek M3. ...Rozděleno na tři části.</p>

To achieve a smoother finish on your print's surface, simply activate ironing in Cura. ...This feature enables you to produce a more polished result.