fleshlight desk mount 3d models

I was getting annoyed with 2 power bricks hanging from the back of my desk so I designed a mount to mount them to the pole structure of my desk.Make sure to print this vertically so the layer lines are running across the pole mounts along it's wide...

This is a simple under desk mount for the Topping MX3 DAC. ... The dimensions are in mm (LxDxH)155x95x37 Thickness 5mm & the holes are 4mm diameter.

This is a Under Desk/Wall mount for lightweight objects with two side tape, it snaps into place in the bracket. ...

I was looking for an adjustable mount for the side of a desk and made adjustments to a favorite of mine

Hot air desk mount Remix of: https://www.thingiverse.com/thing:3348948 <- take screw from here https://www.thingiverse.com/thing:1241872

this is a desk mount for, SABRENT 4 Port USB 3.0 Hub with Individual LED Power Switches (HB-UM43). ...The hub can be found on amazon.

The mount is in two parts left and right. ...you can screw it under the desk with 8 screws There is some room for ventilation. ...

Hi, this is my desk mount for a Microsoft Surface Dock. It's designed to be strong yet lightweight. ...Should require minimal supports to print.

This is a Under Desk/Wall mount for lightweight objects with two side tape, it snaps into place in the bracket.

This is a mount for a toggle switch that I wanted to mount under my desk. It's got a slight upward slant so the switch is easier to hit if the mount is placed at the edge of a desk. Opening is 12.2mm, close to 1/2 inch. Can be drilled out. ... I'm...

... The print took approximately 30 hours and used approximately 272 grams of filament. 5/15/2026 Update: I have added 'laptop-desk-bracket-one-piece.stl,' which comprises the entire half of the mount intended for individuals with larger print beds.

... Print the HeadsetStand STL with the end of the stand facing the build plate. Apply adhesive rubber to the part of the stand that touches your desk. I have a glass top desk and even when the mount is secure, it still tends to slide around slightly.

This Mount is attached on the underside of your desk allowing for easier access and more desk room. I Printed this with NO support regular quality is fine but I've printed at 80% speed no issues. You can use double sided 3M and screws to mount. YOU...

This is a mount that I used to make my computer's audio output available under the lip of my desk. Designed for an 8.5mm OD barrel. ...I used a 5/8" #6 woodscrew to attach the mount to the underside of my desk.

... yet still printable on a 230cm bed. ...Mounts with two screws on underside of desk. I sleeved this with cut road bicycle inner tubes over the upper mount forks to grip the laptop. ...Some sort of friction tape or similar is necessary for this design.

A laptop mount for the side of your desk so you can free some workspace area. ... The mounting was inspired by the [Simplified Headphone Holder](https://www.thingiverse.com/thing:4016621)

The under-desk cable management system features a versatile 30mm and 50mm cable mount design. ...Initial testing involved printing the mounts with PLA, utilizing a 20% infill density to assess structural integrity.

This mount is perfectly compatible with the IKEA Jerker desks. Attached to the mount are rings that securely fasten the material to prevent scratch marks from the screws. ...In my specific setup, these rings support my speakers.

Upright Desk Mount for MacBook Pro 2017 - No Case Required This upright desk mount is designed specifically for a 2017 MacBook Pro, although it may work with other models as well, since testing has not been done. The recommended desk thickness for...

This is a simple clamp mount that can hold your headphones under your desk when you don't need them. There are two frames. One for headphones with a headband width of up to 35mm and one for a width of up to 45mm. Maximum Desk thickness: 65mm...

Human: **FiiO K3 USB DAC Under-Desk Mount**\r\n\r\nEngineered to clamp onto the edge of a workspace with ease, this under-desk mount secures firmly via tiny wood screws.\r\n\r\nThe digital-to-analog converter is snugly held in place by a lip on...

... clamp and clamp bottom. For the Clip I used super glue to mount the desk end onto my desk and then glued the base end to the back of the main mount. ...The base end clip should slide into the desk end to prevent the wheel from tilting up during use.

Designed this to clear up some desk space and mount my HP ZBook vertically to one of the legs on my new SHW 48" Height Adjustable Desk. Uses 4 M5x15 screws and nuts. ...Print Settings Printer: CR-6 Max Rafts: No Supports: No Resolution: .28 Infill: 30...

I hastily whipped up a makeshift mount underneath my desk last night. The result is a bit rough around the edges, and I quickly put it together using Tinkercad. ...Unfortunately, the holes that were supposed to be for M5 screws didn't quite turn out as...

quick model of microphone arm desk mount should fit most IKEA desks without any issues. ... test print out of PLA came out great, fits perfectly snug use with caution, no clamp, no warranty Materials needed: 2x M3 screw 8-22mm long 2x M3 nut 1x...

Remixed design of the original double stream deck desk clamp (https://www.thingiverse.com/thing:3969782) by adding a cylinder modifier for a cable hole.Frame can be mounted either way to have it either above or below desk level. ...You will need three...

... the Alfa holder part. ... I just removed the vertical mount and added in a horizontal one to attach to the back of my desk. ...Space in the groove is 1.7cm to accommodate my desk but can be used on most things smaller with a bit of trusty blu-tack!

I took mistertech's fantastic desk mount headphone holder and modified the clamp to fit my large desk, also adding a ring to securely hold a standard dynamic microphone. The hole is 33mm wide. It's currently printing, but I'm confident it will be...

This is a desk mount for the Fiio K5 Pro, this model can be used for both regular desks and desks with frames underneath (up to 25mm).All that is required is to screw into the bottom of the desk and slide in the K5 (you may need to take off the feet)...

Created a 2 piece mount to keep my laptop out of the way when using at my desk. It is attached to the leg of my VariDesk standing desk. The laptop this was designed around was ~21mm thick and fits quite well. This part is set up to use 4 M3...