flat s hook 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=48499 Print Settings Resolution: 0.3 Infill: 80% Instructions Using the following options: end_angle = -89 top_hook_radius = 5 thickness = 8 start_angle = -30 length = 25 width = 4...

Customized version of http://www.thingiverse.com/thing:48499 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=48499

Flat and strong hook for my indoor vegetable garden

Extremely simple flat and easy to print hook. ...Install with double sided tape or glue.

Extremely simple flat and easy to print hook. ...Install with double sided tape or glue.

I made one side of the hook flat so that you can print it laying down for better strength.

So I went and designed a new whale hook, simplified so it can be printed flat on its side to make sure that weak spot was eliminated. While I was at it, I moved the hook's location, so the gap it is made for is now bigger (30.46mm) to accommodate...

After several months of use my beloved whale started coming loose, as the bottom jaw was a weak spot. So I went and designed a new whale hook, simplified so it can be printed flat on its side to make sure that weak spot was eliminated. While I was at...

... adhesion with my settings. The flat cap provides good coverage to keep everything clean, while the hole on top for hanging also acts as a small anchor point if you happen to lose your towels and they roll off the counter, which has happened before.

Parametric flat radiator hook for bathroom radiator "Korado koratherm AQUAPANEL" with approx. ...dimensions of rib 70x12 mm.I advise to increase height of the hook and stick anti-slip pad on it for better experience.Source code for OpenSCAD:...

Basic flat 17X26 mm magnetic hook holds up to three 10X1 mm neo magnets securely in place. ... Other magnetic hooks can be found at this link: https://www.thingiverse.com/thing:2794729 Magnetic pushpins are available here:...

A VERY sturdy hook for flat-pack shelves.two versions (2 tabs is most secure, but 1 tab is also quite sturdy and stable)Note: this is designed for shelves where the holes are 12mm or larger, and spaced 38.5mm apart (at least, for the two tab...

Designed with canvas framed paintings (frame only, no wire used) in mind; the traditional "Command Hook" has a long "finger" of sorts that tends to protrude/pierce through canvas (when not suspended by wire) material leaving an unsightly "bump" over...

This is just a simple design so I could hang our wifi modem on a flat bar.

Adapted version of espaisocialdefabricacios wall hook \(\). I added a stepped tip and cut off the top part. ...It is great for wall mounted lamps and such because it takes up little space.

... glue, and then gently insert the magnet into its designated space. The print can be resumed without any issues. A nail with its head removed serves as the pivotal pin. I have provided an updated design for the hook that does not feature a logo.

... is a straightforward reinterpretation of the outstanding Maui Fishhook from Moana. ...I've simply dissected it, resized it to suit a 200x200 canvas, allowing you to print each piece flat without any need for support, then bond them together as desired.

Took it on a trip that included a couple lockages and it performed it's duty admirably, if I did wish the tube was a little longer. We'll see how it weathers in the boat this summer. <h1>"1000 Mile" Review</h1> Works so well I made another for a...

S hook.

Flat hook for use with 3M thick tapePrinted on 100% infill on Ankermake M5 with PLA+ (takes ~17minutes)

S HOOK

S-Hook for Pipe 32MM.

S hook for hanging things

S hook for hanging things Category: Organization

Wife wanted hooks (specifically s shaped hooks) to hang measuring cups from shelving.

I fashioned a small S hook to compensate for my coat hanger's limited hooks. ...These makeshift hooks can be conveniently attached underneath the hat rack.

S hook for hanging, potted plants or bird feeders

This is a reimagining of Captain Hook's infamous hook from the classic tale of Peter Pan.

While I was at it, I also created an S-Hook with larger hooks on both sides, making it symmetrical. And, of course, an even larger one. The smaller S-hook features 6.5mm and 19mm hooks. The larger S-Hook boasts two 19mm hooks. The largest S-Hook has...