flat models

Damixa Flat is a design with simple forms, precise and well structured, that integrates into the most diverse environments and conveys a sense of gravitas. ...An easy and objective interface, but with professional style that says this is an accessible...

Automatic Keep-Open Doorstop for Flat Doors. The minimum gap required between the door and the floor is precisely 2.4 millimeters. Conversely, the maximum acceptable gap between the door and the floor must not exceed 5 millimeters. ... For doors with a...

... Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Options Selected flat_bottom stick_width = 8 hole_radius = 3 font_size = 10 Font = orbitron.dxf stick_thickness = 3 message: Angela Font thickness = 5

Design Your Custom Sign Maker Now Visit http://www.thingiverse.com/thing:52734 and Start Designing Today Created with the Thingiverse Customizer - Find it at http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Design Options Using these...

Since I've opted for a flat bottom, it will have a flat base rather than the standard rounded one. To ensure my message gets seen easily, I'll increase its height above the surrounding text with a large font size of 10pt. I want it to stand out on...

http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following settings: flat_bottom set to 1 Font is write/orbitron.dxf selected stick_thickness is precisely set at 3 units Custom message reads: Edna Stick width...

Customize it with these options: labelDepth of -0.3, 2 columns, labelHeight of 8, magnetDiameter of 3.1, batteryDiameter of 14.8, 2 rows, magnetHeight of 3.1, base of 0.9, Orbitron font for labels with text "flat", inside height of 25.5, walls...

In a groundbreaking initiative, a flat heptagon is being designed specifically for printing by members of the public as part of a crowd-printing project aimed at benefiting the South African National Council for the Blind. ...This innovative endeavor...

A novel idea for a 3D-printable 'Flat fastener' facilitates fixed connections. Comprising an anchor strap and click-nut, this design boasts key features such as printing the anchor strap horizontally without support, easy clicking of the nut,...

Videos: - https://www.youtube.com/watch?v=0W5eIGxPlxA [UPDATE] See post: https://www.cloudynights.com/topic/728083-diy-flat-field-panel/?p=12035910 I've finally finished my DIY flat panel. I used: - A 12V DC 160mm LED Panel rom AliExpress with a...

... Radius of central hole measures three millimeters. Flat bottom option is engaged. Custom font chosen is write/orbitron.dxf. Stick thickness stands at three millimeters. Font line weight selected is five units. ...Font size configured at ten points.

A flat spring is a type of coil spring that has been flattened into a two-dimensional shape, typically used in various applications for its ability to store and release mechanical energy efficiently. It offers several advantages over traditional...

I upgraded my plastic bag first aid kit with a flat box. It's designed to fit the smaller Tegaderm sizes, which is usually the first item I put in my kits. The file is intended for printing with flexible filament; it features two ridges that overlap...

Below are the specifications used for customization: font - write/orbitron.dxf, stick thickness of 4, stick width at 9.5, hole radius of 3, flat bottom enabled, font size of 11.5, and font thickness of 6. ...The personalized message displayed is...

The flat worm after printing weighs only 13 grams at a length of 140mm with one perimeter the worm is fully flexible immediately after removal X - 36 mm Y 140 mm z 17 mm keep 100% size ! ...Do not try to shrink it too much .It will narrow the...

Check out the specifications used below to personalize your print: labelDepth (-0.3), columns (4), labelHeight (8), magnetDiameter (3.1), batteryDiameter (14.8), rows (2), magnetHeight (3.1), base (0.9), labelFont (write/orbitron.dxf), labelText...

I got a nice table tripod, with ball head, but even that was to large/high for what I wanted so I made this "flat tripod". Mounting a camera onto is places it right on the ground, and adding a ball head gives you something really small/low. It...

This krytac hop-up arm has been redesigned to accommodate flat/r-hop use cases, where the original arm would flex or bend under pressure. The new design effectively solves this issue by allowing for a more stable setup. Note that some additional...

The design is reminiscent of a flat bear made from plastic beads and then ironed. It was created within Minecraft and processed through Mineways with a 2mm per block calibration. The resulting file was printed on a MakerBot Replicator with settings...

Instructions: Using the following settings: - font_thickness is set at 5 units - bottom shape will remain flat, at a value of 1 - font size is selected to be 10 points high - Orbitron dxf file has been chosen as the font style - radius of each hole...

I swapped out my old plastic bag first aid kit with a flat box that fits snugly around smaller Tegaderm sizes. That's usually the first thing I pack in my first aid kits, and it takes up the most space. The file is tailored to print well with...

Created using Customizer, found at: https://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions: To make use of this option you need to follow these instructions: Flat bottom - Enabled Font: Orbitron Font Size: 10 pt. Stick Width: 8...

Model creted using only reference pictures.

Using the following options: Font = orbitron.dxf Stick width is 8 units thick The font thickness is set to 5 units Message written in the stick reads 'Bruce' Stick size is set to 3 units Hole diameter at the base of the stick is 3 units in radius A...

this is the first part of the floating Discworld model

Modeled using SolidWorks 2019, Rendered to Perfection in KeyShot 9

Here he is in all his glory - good ol' Flat Stanley! I started with a JPG of Stanley and converted it to a .stl at www.selva3d.com. Then, I imported the .stl into TinkerCAD, where I realized that if I printed him as is, his eyes, nose, and mouth...

Tutorial model from https://www.youtube.com/watch?v=7aHbpchu7-c

This model was created using Tinkercad's powerful editing tools, accessible at tinkerCAD.com.

A 3D model of a flathead screwdriver is generated using Catia V5 software and displayed through rendering with KS5.