flashforge spool holder 3d models

Because the end of the filament guide tube would move closer and father away, sometimes I had an issue with filament getting off the spool and tangling or being pulled taught. I designed filament guides the keep it in place and keep the filament from...

This is a revised design for object http://www.thingiverse.com/thing:930910 Intended to fit Taulman 3D's 1 lb spools of T-Glase, Bridge Nylon, and other materials. Modeled after the original, similar in style to Hatchbox's version. ... Utilizes the...

Modification Upgrade for the Flashforge Creator Pro 2015 Spool Holder ø38x91mm Makes it Easy to Add Smaller Spools Without Fretting Over Them Falling Off Specifically Designed to Fit Sainsmart Filament Spools With Ease.

... in Yafo. Print Settings: Printer: FlashForge Creator Pro Rafts: None Supports: Not needed Resolution: 0.3 mm with three shell layers Infill: Twenty percent density Notes: This is my preferred printing method, yielding successful results every time.

made specifically for spools I get from 3D-factory in yafo Print Settings Printer: flashforge creator pro Rafts: No Supports: No Resolution: 0.3 mm and 3 shells Infill: 20 Notes: that's how I printed it, works fine for me Category: 3D Printer...

Created with Customizer! Using the following settings: Instructions To adjust this design, customize the settings below. ... Adjustable Settings: Core Diameter: Set to 36 mm (adjust as needed) Core Depth: Select a depth...

Instructions Using Custom Options Choose Settings to Refine Design With these values in mind, users can now optimize their design: - Core Diameter Set at a Solid 36mm - Percentage Adjusted for a Harmonious Balance of 66% - Core Depth Fine-Tuned...

I needed to save space and access the filament easily. I created this :-)(easy to print NO raft or support needed) 15% infill should be enough.It mounts on the right side top! Works for both - small and normal 1kg. ...filament rolls.𝔗𝔴𝔬...

I needed to save space and access the filament easily. I created this :-)(easy to print NO raft or support needed) 15% infill should be enough.It mounts on the right side top! Works for both - small and normal 1kg. ...filament rolls.𝔗𝔴𝔬...

Customized version of https://www.thingiverse.com/thing:1108314 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1108314

Instructions Using the Following Options: Core Diameter is Set at 36 Percentage is Tied to 66 Percent Core Offset Stands at 3 Core Depth Remains at a Robust 95

I loved the original design but didn't want "Hatchbox Filament" to always stare at me from the back of my printer. The only thing I did was take off those words. ...Thanks for the great design!

The original side loader arm worked great until the stress on the corner of the hook caused it to break. I modified the original loader arm file using 3D Builder to make it thicker so it (hopefully) won't break again. Only the part near the...

Qty 2 risers can be used (one on each side) to raise the existing spool holders (new longer screws may be required). Qty 2 rolls can be used to further raise the spool and accommodate larger diameter spool centres. The resulting clearances are very...

Print out this spool holder for your wood frame printer and install them above the printers for space saving and prevent filament jam. The holder is designed for most of the wood frame printers (3/16" wood panel). It can hold about 3 spools of...

This is a custom filament spool holder designed specifically for the Flashforge Creator Pro, suitable for use with 3D Printz stock filaments. While the standard holder performs admirably, it can be prone to allowing the 3D Printz roll to slide off...

Here's a list of parts needed to print the spool holder: * Bolts: + 4pcs M5 x 25mm (2 bolts for each side) + 2pcs M5 x 30mm (for the middle part) + 2pcs M5 x 40mm (for the front bar) + 1pc M3 x 20mm (to connect to the printer's shell) The left and...

I made this spool holder for my CTC printer, but it should work with every Replicator Dual with a wood shell - unless there are differences in dimensions, in which case please let me know. Other parts needed: Bolts: - 4 PCS M5 x 25mm (back part: 2...

I use (and love) this spool holder on my Replicator 2 but due to the spool hole being circular on the PowerSpec, it wouldn't fit. I could've cut the back panel of the PowerSpec to make the hole square, but what's the fun in that? By no means is...

Components needed:1 x M8x120mm Bolt1 x M8 Nut1 x M8 spacer2 x 608zz bearings