flashforge dreamer mods 3d models

... I also redesigned the bracket to fit over the bottom edge of the side window on the FlashForge Dreamer & Dreamer NX (which I have). Here's part 1 of a 5 part YouTube series about how I remixed this project. ... https://youtu.be/tkaeBiXwaGs

We use a wide range of filaments when printing with our Flashforge Dreamer machines, just like you probably do, which is why you're likely searching for this. I designed this holder to address the issue of other filament spools not fitting neatly...

This is a versatile camera mount that attaches itself to the unused screw posts situated on the upper left-hand side of the inside front of the Flashforge Dreamer / Dremel Idea Builder. It was specifically designed for the ELP 2.1mm wide-angle 5...

We use a lot of different filaments when printing with our Flashforge Dreamer machines, and so does you probable, otherwise you wouldn't search for this? I created this holder to help me solve the issue of other filament spools not really fit inside...

We use a wide variety of filaments when printing with our Flashforge Dreamer machines, and so do you probably, otherwise you wouldn't be searching for this. I created this holder to help me solve the issue of other filament spools not fitting...

To check if your IP Camera will fit: Gap from center mounting screw hole to furthest edge: approximately 61mm Gap from center of mounting screw hole to closest edge (as the Wanscam HW0024 is rounded at the front, this wasn't an issue): approximately...

Under the Extruder Carriage Laser or tool holder/mount for CTC, Flashforge Inventor, Creator, Dreamer. You'll require printing 4 LaserMountSide and 1 LaserMountBase units. To assemble it securely, use Krazy Glue to hold everything together.

Here are the rewritten texts: Filament holder with a FlashForge Dreamer 3D printer.\nI designed this hook for 1 kg Nunus filament, which no longer fits inside the cabin.\nI used an existing prototype (http://www.thingiverse.com/thing:938750) as a...

This is a filament spool holder for the Dremel 3D20 / FlashForge Dreamer. It allows use of 1 kg InLand / eSUN filament and any roll of similar diameter with width less than 66 mm and greater than ~ 60 mm. This design requires four 608 size skateboard...

... to my filament boxes. Print Settings: Printer: Flashforge Dreamer Rafts: Yes Supports: Yes Resolution: 0.2 Infill: 20% Notes: It was printed upright with a raft and supports, using white Innofill PLA with standard medium settings in Simplify3D.

... Modification 1: Clip Adjustment Modification 2: Design Enhancement Printing Settings: Printer: Flashforge Dreamer Raft Support: Disabled Support Material: Disabled Layer Resolution: 0.20mm Infill Density: 30%

File: Reel Adapter.stl Name: Custom Reel Adapter for Makerbot Mini and Flashforge Dreamer Printers PLA Material: Used - 38.12 grams (0.084 lbs), Infill Rate: Set to 11% Size: Prints out to be approximately 63.50 mm (2.5") x 63.41 mm (2.5") x 49.78 mm...

This particular dial gauge is utilized: http://www.amazon.de/dp/B003V8T4ZU/ref=cm_sw_em_r_mt_dp_ZS4gxb03G0JX2 Print Settings Printer: Flashforge Dreamer Rafts: No Supports: No Resolution: 0.20 Infill: 30% Notes: ABS is the preferred material for...

We use a lot of different filaments when printing with our Flashforge Dreamer machines, and so does you probable, otherwise you wouldn't search for this? I created this holder to help me solve the issue of other filament spools not really fit inside...

After numerous trials, I finally understood what is keeping all these print runs in an eternal struggle: a standard drive train system is quite insufficient in keeping this particular sort of TPE material taut on most standard FlashForge models (but...

Remix of **[BV3D's](https://www.thingiverse.com/bkvines)** mount to fit onto my __FlashForge Dreamer__. I used *(40x40x10mm)*, so I have extended the grille out to prevent the gap from smaller sized hot-end fans. Probably not a perfect model, but it...

This is a mounting plate designed to fit in a FlashForge Dreamer (NX) or Dremel 3D printer. The mounting holes for the boards are left intentionally small to be drilled for the appropriate size screws. An additional hex stand-off will need to be...

This is a mounting plate designed to fit in a FlashForge Dreamer (NX) or Dremel 3D printer. The mounting holes for the boards are left intentionally small to be drilled for the appropriate size screws. An additional hex stand-off will need to be...

Print Settings: Printer: FlashForge Dreamer Rafts: No Supports: Yes Resolution: 0.10 mm Infill: 75% or higher Notes: Use ABS due to the high environmental temperature. A high infill percentage increases stability against deformation. Try the best...

Printer Settings Printer: FlashForge Dreamer Rafts: Yes Supports: Yes Resolution: .4 mm nozzle, .2 mm layer height Infill: 100% Notes: You will want to print this upside down. The detail that allows this part to snap-fit into your existing carriage...

Print Settings: Printer: FlashForge Dreamer Rafts: Doesn't Matter Supports: Yes Resolution: 0.1mm Infill: 75% Notes: I strongly advise using ABS due to high environmental temperatures and suggest trying a higher infill percentage to increase...

This is the Flashforge Dreamer glass bed upgrade 5mm shim. This part is the same one that comes with the Makersome Glass Bed Upgrade kit, and it works perfectly with glass plates that are 5mm thick. We re-designed this part to have a little tighter...

Print Settings Printer: Flashforge Dreamer Rafts: Yes Supports: No Resolution: Standard Infill: 20% Notes: I used ABS. My part started curling up and I had to add white school glue to keep it down, so I suggest using a raft. When it's loaded into...

Another quick and dirty, combining a velocity stack with the C style duct cooler's bracket. ...Works on the Dreamer NX, should be fully compatible with the Dremel 3D20. ...Find the original stack and the C duct from the source Things.

All found models of brackets for FIashForge Dreamer for 3mm glass plates did not fit on my device.Because the print bed of the Dreamer is wider than the 230mmx150mm glass plates the plates were not fixed safe on the bed and shifted around. The most...

Because the original print plate of the FIashForge Dreamer is an additional thermal resistance between the heat bed an the glass plate I removed it to decrease the temperature difference between measured (and controlled) temperature of the heat bed...

All found models of brackets for FIashForge Dreamer for 3mm glass plates did not fit on my device.Because the print bed of the Dreamer is wider than the 230mmx150mm glass plates the plates were not fixed safe on the bed and shifted around. The most...

... The "Flashforge" backsplash (that decorative bit of black acrylic standing up behind the print bed) will likely need to be removed to allow for clearance, otherwise installation is just a matter of removing the old duct and installing this one.

This mod is still a work-in-progress, but I'm excited to share updates, photos, and modifications as soon as it's up and running smoothly. **Instructions** I'd like to thank BaronWilliams for creating an amazing fan attachment. His hard work...

Designing an iPad Mini Frame for a Wall Mount Requires Some Creative Tweaks Let's start by adding some smart features to make the design truly exceptional. The main goal is to allow the user to slide their iPad in and out of the frame effortlessly,...