flashforge creator pro parts 3d models

made specifically for spools I get from 3D-factory in yafo Print Settings Printer: flashforge creator pro Rafts: No Supports: No Resolution: 0.3 mm and 3 shells Infill: 20 Notes: that's how I printed it, works fine for me Category: 3D Printer...

Printer Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 mm Infill: 20% Post-Printing Make sure the shim is perfectly flat to avoid springiness while pushing the Z endstop switch, which could...

I find that on my FlashForge NEW Creator Pro (received November-2016), parts with large surface areas are difficult to remove from the bed plate. For example, the first time I printed out the orange bird house (thingi1351023), I did so on a glass...

This is a reworked adaptation of Stigern's 0.25" Z-axis spacer for the FF Creator Pro.\nI'd procured a 5mm glass bed from my local vendor, so I rewrote it to create a 5mm version of my own. During that process, I also designed a 3mm edition.\n\n \n...

... in Yafo. Print Settings: Printer: FlashForge Creator Pro Rafts: None Supports: Not needed Resolution: 0.3 mm with three shell layers Infill: Twenty percent density Notes: This is my preferred printing method, yielding successful results every time.

A modified z-axis limit switch shim based on salbemerson's design for use with the Printz Printer Plate on the FlashForge Creator Pro. The plate measures approximately 1/8" thick or around 3.35mm. It was printed at low resolution and installed on...

I recently purchased a FlashForge Creator Pro for rapid prototyping at work and found that the included filament spool holders were excessively large in diameter to fit my stock of Hatchbox filament spools. Unlike other designs on Thingiverse, this...

Flashforge Creator Pro Y-axis step motor mounting bracket. I modeled a stronger design verse the factory bracket. I thought the belt was very close to the bracket so I created a version that has a cutout for the belt. You can select which one you...

This is a custom Raspberry Pi 3 sleeve case featuring a camera ribbon cable pass-through, designed specifically for replacing a spool holder on Flashforge Creator Pro. This innovative design thoughtfully maintains the existing spool holder rather...

You'll need some M3 screws and nuts, of which there are several extras in the hardware bag that comes with the FlashForge Creator Pro. ... One note: if your creator comes with a back plate behind the build platform, you'll need to remove it or it will...

... Thanks, fdk. Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: .20 Infill: 20% Notes: 3 top layers, 3 bottom layers, 2 outline perimeter shells printed on a 95-degree bed at 235 extrusion temperature with ABS.

**The motivation for this project** I really like my FlashForge Creator Pro, but there's always been one thing that kept bugging me - the lack of variable speed for the cooling fan. This got especially problematic after installing an all-metal...

In short, this is a solution to add advanced and fully automated variable fan speed control to a MightyBoard-based 3D printer like the FlashForge Creator Pro. These printers only have a binary toggle for the fan and there is no straightforward...

There are many shims available but I couldn't find any for the 2016 FlashForge Creator Pro which seems to have screws in different places than other models, so here's a remix that fits. Ready-to-use models are available in thicknesses from 2 to 6 mm...

These are custom designed shims that have been perfectly matched for use with a Flashforge Creator Pro, which was built mid-2015. They are specifically designed for 3mm or 4mm glass bed upgrades of similar size. Instead of leaving a gap around the...

To upgrade your Creality Ender 3 to a Creator Pro, simply add a glass bed. However, this requires removing the existing bed logo plate. ...It can be easily inserted and removed by snapping it into place.

Unfortunately, the FlashForge Creator Pro lacks a fan speed controller because the fan is hooked up to the EXTRA output of the mainboard, which can only be toggled and has no PWM capabilities. It's possible to create and install a custom build of...

Unfortunately the FlashForge Creator pro lacks a fan speed controller, because the fan is hooked up to the EXTRA output of the mainboard, which can only be toggled, it has no PWM capabilities. It is possible to create and install a custom build of...

The mount is strong and perfectly fits my QIDI Tech printer; I'm confident that it could also be used with Flashforge printers. In one picture, you can see me testing it with my utility bin. Print Settings Printer: QIDI Tech ...

Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Supports: No Resolution: .2 Infill: 20 Notes: I recommend PLA. ...Everything can be printed at .2mm layer height except for Pi_Zero_Case_Camera_Swivel.stl, which must be printed at .1mm...

Still working on that part. I added just the case bottom with no mounts for other projects. Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Supports: No Resolution: .2 Infill: 20 Notes: I recommend PLA. ...Everything can be...

The parts are for upgrading the FFCP with 4x2mm bowden tubes. because of the higher flexibility. ... BR Sepp

The piece with a section cutout is designed specifically for the back right corner because the bearing mount obstructed my original part on my machine. Printer Settings Printer: QIDI Tech Rafts: None Supports: None Resolution: 0.12mm ...

... into the space between the sheet metal frame, resting comfortably on the body. Check out the picture for additional details. I've attached the Solidworks part file. Print settings are contained within the zip file. ...Support is an optional feature.

It fits snugly into the space between the sheet metal framework and rests comfortably on the body, as you can see from the attached picture for more details.\n\nThe Solidworks part file is included, along with print settings in the zip file. ...Support...

all i did was added some nice script flash forge dual extrusion logo on the side because well if we have duallies why not use em especially on the machine parts we print for said machines! ...and also made a second wide enough to fill the slot you...

Especially when printing machine parts for said machines! ...I also whipped up a second logo that's wide enough to fill the slot you insert the holder into - a thoughtful touch for those who plan on printing with ABS, giving them an added layer of...

... the Sheet Metal Construction and Sits Nicely on the Body, Check out the Picture Below for More Details. Included is the Solidworks Part File. Print Settings are Included in the Zip File. ...Support is Optional but Recommended for a Smooth Finish.

Print Settings: Printer: Qidi Tech Rafts: No Supports: Yes Resolution: 0.12 Infill: 30% Notes: I employed support for both parts, adding extra support to the cover hinge pegs to ensure they emerged rounded and smooth. The cover was printed in ABS...

You can employ either the left, right, or both parts, which are mounted into the open corner slots of the printer. They are designed to flex and allow the front door to slide smoothly into the hinge holding area without removal. Print Settings: ...