flashforge creator pro glass bed 3d models

Weiterentwicklung des Filament Wandhalters, zu dem Ersatzhalter für den Falaschforge, Creator Pro /2

Hi There, The main wire set, which I've dubbed the Umbilical Cord on my FlashForge Creator Pro, has taken to bending itself to one side and now relentlessly rubs against the plexiglass top. This irritation prompted me to design a straightforward...

I'd like to share my print settings with you: Printer - FlashForge Creator Pro, Rafts - No, Supports - No, Resolution - Medium, Infill - 50%. This design prints extremely quickly and efficiently. ...To get the best results, I recommend using a strong...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .2 Infill: 15-20% Notes: I strongly recommend printing the pieces at .2 resolution to ensure accurate results. My own prints came out perfectly, with no need for...

GoPro Mount for Flashforge Creator Pro. Two arm lengths are available, 45mm and 60mm. This mount will hang from the front of the printer, with a hump in the middle to fit over the screw. (This is designed specifically for those who paid $1,200;...

ServiceTray for FlashForge Creator Pro 2016 fits perfectly into the top hole on this machine, making maintenance of the extruder, fans and nozzles much simpler. This useful accessory is designed to be printed as a single piece, but an alternative...

GoPro Mount for Flashforge Creator Pro. Two downward arm lengths available, 45mm & 60mm. This mount will be attached to the front of the printer, featuring a hump in the middle designed to go over the screw that's standard on printers costing $1,200...

GoPro Mount for Flashforge Creator Pro. This mount attaches to the front of your printer, with a raised section in the middle to fit over the screw. Designed specifically for those who invested in the higher-end model, this mount takes advantage of...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

A perfect companion for the replacement filament tube holder, this replacement for the Creator Pro 2020 standard spooler was created to remedy two of its flaws: (a) On the standard spooler, the flexible clips used to remove the spool are hard to...

By following these simple yet effective maintenance procedures, I'm able to keep my Flashforge's glass bed in top condition, ensuring optimal performance and extending its lifespan. ...A well-maintained glass bed is essential for achieving high-quality...

So I had to purchase the only lid FlashForge provides for the 2016 creator pro, which is the unibody lid. If you're not aware, this lid is 12mm too short to sit properly on top and there are no brackets to secure it in place. As a result, here's my...

Mount for the Paneldue i5, it is made to replace the original LCD display of the Creator Pro 2016 and uses the same screws.

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20 or less Infill: 25% - 100% Notes: When printing the hanger and knurled knob, add a G-code command to pause the print just before covering the captive nut hole...

Printer Settings: * Printer: FlashForge Creator Pro * Rafts: No * Supports: No * Resolution: 0.3 * Infill: 25 Post-Printing Assembly: Insert the Inside Clamp.stl from within the printer, ensuring it aligns flush with the back of the device. Next,...

Here's a link to that little handle: http://www.thingiverse.com/thing:1241895 My Print Settings Printer - I used the Flashforge Creator Pro, a great printer. Rafts - I didn't need any rafts for this thing. Supports - My printer could handle some...

The spool holders provided with the FlashForge Creator Pro (2016 version) have very limited dimensions, unable to accommodate most of my spools. Either they're too wide or their hubs are too small to fit on the manufacturer's holders. As a result, I...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

I'm building a hinge for the dome of my Creator Pro, and I had to get creative since I was tired of constantly moving it around. The design requires blocks to support the weight of the dome itself, which presented a challenge. To address this issue,...

The latest edition of the Flasforge Creator Pro is designed with a proprietary snap-in mechanism, which unfortunately doesn't mesh seamlessly with the spools offered by many other manufacturers.

Simple Spool Holder for the Creator Pro, I'm not impressed with most on the site so far. ... Hardware: 1/4-20 bolt 1/4-20x3.5 inch hex head screw I hope these parts are helpful to you!

Simple Spool Holder for the Creator Pro, I wasn't a fan of most on the site so far. ... Hardware: 1/4-20 Nut 1/4-20x3.5" Hex head bolt Hope you find them useful!

Here is the spun text: Creator Pro Spool Holder for 1kg ESUN Brand Filaments \n Customized version of http://www.thingiverse.com/thing:1108314 \n Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1108314

Print Settings: Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 mm Infill: 14% Filament: Renkforce ABS Black Post-Printing: If the holes come out too small, use a 3 mm drill for the screw holes and...

... as they would fit just as well. I've also included a foot with a glue holder, or you can simply print four of the other foot designs. Print Settings: Printer: FlashForge Creator Pro2016 Rafts: No Supports: Yes Infill: 30% Notes: Printed in ABS.

This Thing offers both a replica of the top plate of the 2016 FlashForge Creator Pro (unsure whether this is different on older models), and an improved version (‘v2’ suffix). This is the part that connects the umbilical cord and the filament guide...

This is to add ABL to Creator Pro, I currently have Marlin flashed to my original motherboard. i had to add mins to mother board for the ABL PWM, also move the fan to the back of the extruder carriage. Not required but my current set up I removed one...

It's worth noting that you'll need some kind of mainboard upgrade as the one that comes with the Creator Pro/Replicator/QIDI/etc cannot really handle this well on its own. I personally converted mine to a Duet 2 Wifi. X/Y offset for me was 37 and...

It's worth noting that you'll need some kind of mainboard upgrade as the one that comes with the Creator Pro/Replicator/QIDI/etc cannot really handle this well on its own. I personally converted mine to a Duet 2 Wifi. X/Y offset for me was 37...

I created this to make swapping spools easier without struggling with the holder on the Flashforge.\r\nYou simply need a base plate and print adapters for your spools, which can be left attached to an adapter, allowing you to hang them from the wall...