flashforge creator pro 2 3d models

GoPro Mount for Flashforge Creator Pro. Two downward arm lengths available, 45mm & 60mm. This mount will be attached to the front of the printer, featuring a hump in the middle designed to go over the screw that's standard on printers costing $1,200...

ServiceTray for FlashForge Creator Pro 2016 fits perfectly into the top hole on this machine, making maintenance of the extruder, fans and nozzles much simpler. This useful accessory is designed to be printed as a single piece, but an alternative...

Print Settings: Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 mm Infill: 14% Filament: Renkforce ABS Black Post-Printing: If the holes come out too small, use a 3 mm drill for the screw holes and...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

A perfect companion for the replacement filament tube holder, this replacement for the Creator Pro 2020 standard spooler was created to remedy two of its flaws: (a) On the standard spooler, the flexible clips used to remove the spool are hard to...

So I had to purchase the only lid FlashForge provides for the 2016 creator pro, which is the unibody lid. If you're not aware, this lid is 12mm too short to sit properly on top and there are no brackets to secure it in place. As a result, here's my...

This is to add ABL to Creator Pro, I currently have Marlin flashed to my original motherboard. i had to add mins to mother board for the ABL PWM, also move the fan to the back of the extruder carriage. Not required but my current set up I removed one...

Mount for the Paneldue i5, it is made to replace the original LCD display of the Creator Pro 2016 and uses the same screws.

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20 or less Infill: 25% - 100% Notes: When printing the hanger and knurled knob, add a G-code command to pause the print just before covering the captive nut hole...

Printer Settings: * Printer: FlashForge Creator Pro * Rafts: No * Supports: No * Resolution: 0.3 * Infill: 25 Post-Printing Assembly: Insert the Inside Clamp.stl from within the printer, ensuring it aligns flush with the back of the device. Next,...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

Here's a link to that little handle: http://www.thingiverse.com/thing:1241895 My Print Settings Printer - I used the Flashforge Creator Pro, a great printer. Rafts - I didn't need any rafts for this thing. Supports - My printer could handle some...

The spool holders provided with the FlashForge Creator Pro (2016 version) have very limited dimensions, unable to accommodate most of my spools. Either they're too wide or their hubs are too small to fit on the manufacturer's holders. As a result, I...

Simple Spool Holder for the Creator Pro, I'm not impressed with most on the site so far. ... Hardware: 1/4-20 bolt 1/4-20x3.5 inch hex head screw I hope these parts are helpful to you!

The latest edition of the Flasforge Creator Pro is designed with a proprietary snap-in mechanism, which unfortunately doesn't mesh seamlessly with the spools offered by many other manufacturers.

Here is the spun text: Creator Pro Spool Holder for 1kg ESUN Brand Filaments \n Customized version of http://www.thingiverse.com/thing:1108314 \n Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1108314

Simple Spool Holder for the Creator Pro, I wasn't a fan of most on the site so far. ... Hardware: 1/4-20 Nut 1/4-20x3.5" Hex head bolt Hope you find them useful!

It's worth noting that you'll need some kind of mainboard upgrade as the one that comes with the Creator Pro/Replicator/QIDI/etc cannot really handle this well on its own. I personally converted mine to a Duet 2 Wifi. X/Y offset for me was 37 and...

It's worth noting that you'll need some kind of mainboard upgrade as the one that comes with the Creator Pro/Replicator/QIDI/etc cannot really handle this well on its own. I personally converted mine to a Duet 2 Wifi. X/Y offset for me was 37...

I'm building a hinge for the dome of my Creator Pro, and I had to get creative since I was tired of constantly moving it around. The design requires blocks to support the weight of the dome itself, which presented a challenge. To address this issue,...

... as they would fit just as well. I've also included a foot with a glue holder, or you can simply print four of the other foot designs. Print Settings: Printer: FlashForge Creator Pro2016 Rafts: No Supports: Yes Infill: 30% Notes: Printed in ABS.

Use these components to attach 1/8 inch borosilicate glass from http://www.mcmaster.com/#8476k74 to your Creator Pro machine. ...I fabricated this component using 618 nylon with a layer thickness of 0.1 mm and 50% fill rate, which is probably...

Summary Mount 1/8" borosilicate glass using http://www.mcmaster.com/#8476k74 to secure it to your Creator Pro. To assemble, follow these steps: I attached this component in 618 nylon with .1mm layers and 50% fill. ...It's likely more than necessary...

This Thing offers both a replica of the top plate of the 2016 FlashForge Creator Pro (unsure whether this is different on older models), and an improved version (‘v2’ suffix). This is the part that connects the umbilical cord and the filament guide...

These custom-made glass plate bed clips are designed specifically for the 1/4-inch borosilicate glass that FlashForge USA sells online. The clips I created use ABS filament as their material. My main goal was to create an easier alternative to...

I created this to make swapping spools easier without struggling with the holder on the Flashforge.\r\nYou simply need a base plate and print adapters for your spools, which can be left attached to an adapter, allowing you to hang them from the wall...

One of the Creator Pros we inherited had cracked feet, so it could no longer rest on the little rubber pads attached to the base. This foot is meant to prop up the printer using existing screw holes on the printer. ... To print the different sides,...

... 123D Design software (Free) and exported an STL file for printing. I used digital calipers to determine the average thickness of the acrylic and built a -2 degree taper onto the inside edge to supply the holding force so it will stand independently.

This is far better than most others out there and it seamlessly integrates into the case and isn't noticeable.\nI am currently working on designing a Pi 2 case that will shorten the length of the required cable. Right now I am using a 75cm/750mm 15...

Spool holder for Flashforge Creator Pro 2016 2 x Screws, 3mm in diameter and 8-15mm long are required 31mm is the recommended diameter for 90mm wide spools If different sizes are needed, just let me know: editing takes only seconds Print Settings...