flashforge creator pro 2 3d models

Here are IGES and STL files representing all the components I've measured and modeled so far for the Flashforge Creator-X extruder assembly. ...Next, I'll focus on modeling the actual extruder unit.

The slots are enlarged to accommodate a Flashforge Creator, and the spring slots are made larger for easier assembly. The slots are also more centered, necessitating a height increase so the printer's bottom clears the spring when in position. ...My...

Filament guide cap =============== Most simple and strong filament tube cap, that original. ... Specialy for flashforge creator 3 dual extruder printer. ... Recommended one tree-like support in centre of hole.

This is a Prusament spool holder / washer for a Flashforge Creator 3 printer I noticed there is a groove on the inner ring of the spool that jams as it unwinds this provides a smoother surface to roll on

For installation instructions, see below: Models designed in SketchUp, sliced in Simplify3D, printed on a Flashforge Pro at 45% infill using a 0.2mm nozzle and 230C in white ABS filament. Preparation: The small holes where M3-sized bolts for...

This clever little gadget effectively silences the whining jet engine noise produced by the FlashForge Creator X when idle. The source of this annoying hum is a small 20mm fan at the bottom of the case, which cools the stepper motor drivers. I...

The 120mm fan mount attaches to the front of a FlashForge Creator for enhanced cooling, preventing PLA from drooping during overhang printing at 180C. Standard fan screws may not fit due to narrow holes; zip ties can be used as an alternative. A...

Coil Support Extension for 2.3 kg Users

So I salvaged a Flashforge Creator - possibly a Replicator Dual knockoff - along with a couple of cassette-like filament reels branded Colido and QiLive, whose standardization remains unclear... and figured it would be a good starting point to design...

This is my initial design submission for Thingiverse: a 3kg spool holder tailored specifically for my FlashForge Creator 3. The spindle is mounted at a 45° angle to the printer's body, and it features a 5° incline to prevent the spool from toppling...

... tube holder designed specifically for a QIDI Tech-1 printer. ... It's also highly likely to fit the Flashforge Creator since QIDI essentially replicated that printer's design. ... To print this replica, place it face down and avoid using any supports.

I'm holding two custom spool spacers alongside my FlashForge Creator. These spacers were designed specifically for this 3D printer and can be found on Thingiverse under the ID #970261. ... This model was created using Tinkercad, a powerful online CAD...

... drive gear slipping or skipping when employing material with inconsistent diameters. ...This innovation is a modification of another upgrade on Thingiverse, designed specifically for Flashforge Creator Dual Extruder models featuring grooved bearings.

To prevent filament tangles on the FlashForge Creator, you can use varying-size sleeves to hold the spool almost snug but not too tight for easy turning. The sleeves come in different sizes to accommodate various spool thicknesses and 'wells'.

The cutout for the SD card in the wooden case of the Flashforge Creator is oversized compared to the SD card reader inside the unit. This often results in missing the reader altogether, causing the card to drop into the case instead. This...

... along with one wider mount. First, remove the brass inserts from the broken axis and snap them into place using some pliers. Printer Settings: Printer: Flashforge Creator X Rafts: No Supports: Yes Resolution: 0.30 mm Infill: 100% Notes: 255° F

... Remove the brass inserts from the broken axis mount and snap them into these new ones with some pliers. Print Settings: Printer: Flashforge Creator X Rafts: No Supports: Yes Resolution: .3mm Infill: 100% Notes: PETG at 260° F

Drilling the hole is very easy, it is only 2mm 3) If you are using Flashforge Creator (if it another similar model, measure carefully before printing), print the first piece), print the first piece, try if it fits well, if Yes then print the other 3...

This is a replacement carriage for the Flashforge Creator Pro. This is still a work in progress! But it's currently being used in my machine! This is a Single Extruder Modification; it may or may not work with the factory firmware. It's working in...

This is a file to laser cut a door for the Flashforge Creator Dual Original from your choice of acrylic. Please note the hinges are mounted at the top. I have provided a DXF and Illustrator file plus the original SLDPRT source file. ...You will have...

This is a file to laser cut a door for the Flashforge Creator Dual Original from your choice of acrylic. Please note the hinges are mounted at the top. I have provided a DXF and Illustrator file plus the original SLDPRT source file. ...You will have...

The FlashForge Creator Max enjoys a trusted companion in the form of a versatile filament spool holder. This reliable accessory seamlessly integrates with numerous third-party filament reels, ensuring hassle-free printing experiences. ...Thoroughly...

This adapter secures the cooling fans and heatsink on the FlashForge Creator X, positioning them at the rear of the extruder rather than the front. This design grants improved access to observe filament flow into the nozzles while maintaining...

I'm modifying the design to accommodate standard 1kg large hub spools on the Creator Pro's stock spool holder. ...This adaptation was created using Tinkercad, and you can edit it directly at https://www.tinkercad.com/things/lGLFc8rIsd5

Human: Custom FlashForge Creator Mod of Replicator Cooler Optimized for Enhanced Performance My key modifications centered on enhancing structural integrity, tailored compatibility with FlashForge hardware, and adjustable air velocity to optimize...

This is not an STL but vector files so you can create your own print file. This is a file to laser cut a door for the Flashforge Creator Dual Original from your choice of acrylic. Please note the hinges are mounted at the top. I have provided a DXF...

I recently acquired a Creator Pro printer and discovered that the filament didn't sit properly on the holder provided with the device. To resolve this issue, I designed a new holder based on the original one. ...This modification aims to improve the...

I wanted to modify my FlashForge Creator dual to a single hotend with dual extrusion. I had purchased the NF TC01 hot end and started tinkering with my printer. I am a NOVICE, I learned 3D design three weeks ago and have been using Fusion 360 for my...

To install bearings on a FlashForge Creator, loosen pulleys, slide shaft to the right, add two 5x11x4 bearings, and position through left pulley and sleeve. Repeat for both shafts. Insert a pillow block with nuts in slots, pop a bearing inside,...

This bracket securely holds a phone onto a Flashforge Creator, utilizing the phone as a webcam to monitor prints remotely from any location. Angled slightly downward for optimal view, this bracket displays the top of each print, providing critical...