flashforge creator pro 2 3d models

A spacer to fill the gap between the mount & top plate of the things with the same name.

I've been told that 3D Hero brand of filament on Amazon gets rave reviews for its high quality and low cost. So, I checked it out myself when my normal brand was out-of-stock and needed to finish a project ASAP. When the filament arrived, I found a...

TO INSTALL GLASS WITH CLIPS, INSERT THE GLASS INTO THE FRONT CLIPS FIRST AND THEN SECURE IT FROM THE BACKSIDE. ENSURE THE FRONT CLIPS SLIGHTLY OVERLAP THE GLASS PLATE TO ACHIEVE A PROPER FIT. THINK OF IT LIKE PUTTING A BATTERY COVER ON A REMOTE...

Created with Customizer! Using the following settings: Instructions To adjust this design, customize the settings below. ... Adjustable Settings: Core Diameter: Set to 36 mm (adjust as needed) Core Depth: Select a depth...

I found that my original version tended to rock itself loose when the tubes pulled against it. ...This may be only my printer, but I found that by extending it like this and using all of the mounting clips the problem was resolved.

They stumbled upon a YouTube video showcasing an ingenious 3D printed part, which immediately caught their attention. However, one major inconvenience stood in the way: switching spools was a tedious task. Determined to find a solution, they decided...

This shim fits as shown to trigger the Z axis end stop sooner to account for the thickness of the PRINTinZ flexible printer plate. All plates are slightly different in thickness, but 4.5mm is the average. Use the bed leveling screws as needed to...

Customized version of http://www.thingiverse.com/thing:1502857 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1502857 Instructions Using the following settings: Indicator hole offset set to 8. Eps...

I upgraded my FFCP just before active cooling fans became a standard part of printers, roughly a month beforehand. It's always been a challenge managing the active cooling system. I've finally had enough and ordered a substantial 120mm fan that plugs...

I checked out a few of these and they didn't make the cut with me. Just my personal taste is what matters here, right? This design makes sure the wires don't scrape against the edges of the canopy, so you won't have to think about them getting stuck...

Under constant revision to meet evolving expectations

This is a remix of the original https://www.thingiverse.com/thing:1396391 Really liked the idea of the rear fan with my flexion kit so I edited the original to fit! Still supports the original screws and fan mods! ...Added large holes at the top to...

My FlashForge Creator Pro was scratching up the floor due to one of it's original feet being ripped off so I decided to whip up a new foot to replace the original. ...Keeps it stable and keeps the floor safe.This foot fits the original screw and...

One of the extruder filament inlet caps broke off Flashforge Creator 3 printer, so I designed a replacement.

It seemed like a great fit for my FlashForge Creator X with metal frame, which is essentially the same printer as the FlashForge Creator Pro but without the plastic cover. After installation, the 5015 fan case was sitting about 3mm too high on my...

3D printed - Integrated Extruder cover and Filament Guide for a FlashForge Creator 3. ...Both left and right covers are included in the files.

New spool holder for old-type (wooden) Flashforge Creator. Fits standart 1kg filament spools. ...You should rotate holder model upside-down in your slicer.

This Dial Indicator holder, designed for FlashForge Creator rails, features a central 8mm hole and two 6mm x 6mm magnet-holding holes. ...Simple to print and install.

I've purchased the Ecubmaker Fantasy Dual Extruder Bracket directly from the manufacturer, and I'm interested to know whether it's compatible with my Flashforge Creator.

Customized version of https://www.thingiverse.com/thing:1949142 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1949142

Customized version of https://www.thingiverse.com/thing:1949142 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1949142

Print Settings: Printer: Flashforge Creator Pro 2016 / Makerbot Rep2 Rafts: Doesn't Matter Supports: No Resolution: 0.3 Infill: 15% Notes: There is no special setting or approach required to print this part. ...Simply use your default settings for the...

I developed this for my Flashforge Creator X, but it should work with any Flasforge Creator Pro or similar Makerbot Dual clone as long as the X carriage dimensions are the same. This assembly allows you to replace the original dual "MK10" extruder...