flashforge creator 4 3d models

Additional Spool Holder for the Flashforge Creator Pro 2 The spool holders supplied for the Creator Pro 2 are very thick, and are built for a very specific reel diameter. ...This replacement will allow you to use reels with smaller centers than the...

I was able to get Cura 3.6, Cura 4.2.1, and Cura 4.4.1 working with my FlashForge Creator Pro 2016 for all single extruder prints. I haven't tried any other versions of Cura, but any versions between 3.6 and 4.4.1 will likely work as well. This thing...

Accessory to Prevent Air from Entering the Flashforge Creator Pro 3D Printer Port The Flashforge Creator Pro 3D printer is a high-performance, user-friendly device that produces precise and detailed prints with ease. However, one crucial aspect of...

This is a remix from GFalgiano thing:1055138 to fit flashforge creator pro 2 Just a simple bracket with flashforge logo to bring the filament tubes outwards for easier use, and to prevent the filament from slipping off the spool and getting tangled...

The 120mm fan mount attaches to the front of a FlashForge Creator for enhanced cooling, preventing PLA from drooping during overhang printing at 180C. Standard fan screws may not fit due to narrow holes; zip ties can be used as an alternative. A...

Print Settings: Printer: Flashforge Creator Pro (2016) Rafts: No Supports: No Resolution: 0.2 Infill: 100% Post-Printing Installation: Remove the bolts, fan grill, and spacers from the fan, then install this fan guard in its place and reinstall the...

------------------- I dislike the spool holder of the FlashForge Creator Pro 2016. Smooth rotation can be difficult depending on the filaments manufacturer. I have tested various systems and now use my own design. This system works with both big...

The following settings were used for this print: Printer: FlashForge Creator Pro Rafts: No rafts were needed for this print. Supports: Yes, supports are included in the design to prevent warping or sagging. Resolution: The resolution of this...

This is my initial design submission for Thingiverse: a 3kg spool holder tailored specifically for my FlashForge Creator 3. The spindle is mounted at a 45° angle to the printer's body, and it features a 5° incline to prevent the spool from toppling...

... the frame-end to the frame as shown in the photo. The link and Motor-End remain unchanged and fit perfectly on the Flashforge creator pro. Print Settings Printer: Flashforge Creator Pro Rafts: No Supports: Yes Resolution: 200 micron Infill: 45%

... Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: Medium Infill: 85% I used a high Infill of 85% to ensure this tool is sturdy and robust, making it perfect for everyday use with my ABS printer set at 230 degrees.

This mount fits both a GoPro and a webcam (or any camera of similar size with standard tripod mount) right onto the front of a Flashforge Creator Pro 2016.\r\nWith cameras taken off, the door still opens and closes fully without removing the mount...

So I salvaged a Flashforge Creator - possibly a Replicator Dual knockoff - along with a couple of cassette-like filament reels branded Colido and QiLive, whose standardization remains unclear... and figured it would be a good starting point to design...

This design is specifically made for the 2015 Flashforge Creator Pro and might fit some compatible models (QIDI Tech, CTC, etc.), but it will not work with the 2016 Creator Pro. It fits 'buckle' style mounts - see the pictures to get an idea of how...

The shape is designed for the flavors of the FlashForge Creator Pro (2016 edition) that have long-shaped feet, but they will fit any machine with feet shaped like a rounded rectangle about 48×17mm in size, at least 2 mm high. Of course you can scale...

After discovering that pre-existing designs for filament tube holders wouldn't fit inside my new FlashForge Creator Pro, I made the decision to create my own design.\nThis is the second version, designed entirely from scratch! The piece's dimensions...

... Printer Settings: Printer Model: Flashforge Creator Pro 2016 Raft: Disabled Supports: Required for easy removal from the print bed Resolution: 0.2mm Infill Percentage: 15% Printing Recommendations: ABS or PLA can be used for printing this piece.

... tube holder designed specifically for a QIDI Tech-1 printer. ... It's also highly likely to fit the Flashforge Creator since QIDI essentially replicated that printer's design. ... To print this replica, place it face down and avoid using any supports.

... surface. ...Issues arose with extruder contact since the glass I'm working with is thinner than what those clips were initially engineered for. Printer Settings Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .2 Infill: 30% Notes:

To prevent filament tangles on the FlashForge Creator, you can use varying-size sleeves to hold the spool almost snug but not too tight for easy turning. The sleeves come in different sizes to accommodate various spool thicknesses and 'wells'.

... access and management. ...When opting for a wall-mounted custom spool holder like mine, it becomes an essential accessory due to the Flashforge Creator Pro's standard large spool holders, which often fail to accommodate most spools from other brands.

... from falling into the hole on the right side of the printer. ... Designed exclusively for the FlashForge Creator Pro 2016 model! ... Additionally, I've created a center cover, which can be found at this link: https://www.thingiverse.com/thing:2515069

I'm holding two custom spool spacers alongside my FlashForge Creator. These spacers were designed specifically for this 3D printer and can be found on Thingiverse under the ID #970261. ... This model was created using Tinkercad, a powerful online CAD...

I modified the drain cleaner design from jmsaltzman to make it compatible with a FlashForge Creator Pro. To print it successfully, place the model at a 30-degree angle so that it prints diagonally across the bed. ...Although it printed well and should...

This is a door holder with a minimalist design, tailored specifically for the FlashForge Creator Pro 3D printer model. Its compatibility with other models remains unverified at this point. This particular project was created using Tinkercad's online...

I've designed these filament holders for the Flashforge Creator Pro 2 that i have. these are under an angle to keep your filament roll on it. there are several options to choose from here. 20mm, 30mm, 40mm and 50 mm with a small angle and...

... insertion. ...V2 - extended so we pull from the center of extra-wide spools (i.e. Alchemist) Print Settings Printer: FlashForge Creator Pro 2016 Rafts: Not Required Supports: Not Necessary Resolution: .3mm Infill: 20% Notes: Three perimeters are used.

... Printer specifications include a model number and name, which is the FLASHFORGE CREATOR PRO. Raft requirements can be disregarded since it doesn't matter in this case. Supports will be generated for the print job because it has been set to yes.

FlashForge Creator Pro users can now breathe a sigh of relief as the innovative Bowden holder prevents the pesky tube from pressing against the extruder, thereby solving one of the most frustrating problems with extrusion that has plagued them for...

This spool holder mounts directly onto the rear of a Flashforge Creator Pro, accommodating spools up to 1 centimeter in diameter. ...Included with this design is the original .ipt file, allowing users to easily modify the dimensions as needed for their...