flashforge creater pro 3d models

... the different sides, mirror this file in the slicer. Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: No Resolution: 0.2-0.3mm Infill: 35% Filament: Hatchbox PLA Notes: It also works in ABS Category: 3D Printer Parts

I modify this blower duct http://www.thingiverse.com/thing:560790 to fit my FlashForge Creator Pro. I used a SUNON GB1205PHV1-8AY.GN (http://fr.farnell.com/sunon/gb1205phv1-8ay-gn/turbine-50x50x15mm-12vdc/dp/1568490) with this blower duct. Do not...

... the different sides, mirror this file in the slicer. Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: No Resolution: 0.2-0.3mm Infill: 35% Filament: Hatchbox PLA Notes: It also works in ABS Category: 3D Printer Parts

Hi There, The main wire set, which I've dubbed the Umbilical Cord on my FlashForge Creator Pro, has taken to bending itself to one side and now relentlessly rubs against the plexiglass top. This irritation prompted me to design a straightforward...

I'd like to share my print settings with you: Printer - FlashForge Creator Pro, Rafts - No, Supports - No, Resolution - Medium, Infill - 50%. This design prints extremely quickly and efficiently. ...To get the best results, I recommend using a strong...

I printed a new one today using Hatchbox yellow ABS with support material and got very good results (slicing with Simplify3D). This is a customizable holder for Flashforge Creator Pro filament guide tubes. It holds the end of the tubes away from the...

GoPro Mount for Flashforge Creator Pro. Two downward arm lengths available, 45mm & 60mm. This mount will be attached to the front of the printer, featuring a hump in the middle designed to go over the screw that's standard on printers costing $1,200...

GoPro Mount for Flashforge Creator Pro. This mount attaches to the front of your printer, with a raised section in the middle to fit over the screw. Designed specifically for those who invested in the higher-end model, this mount takes advantage of...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .2 Infill: 15-20% Notes: I strongly recommend printing the pieces at .2 resolution to ensure accurate results. My own prints came out perfectly, with no need for...

... This holder is customizable for Flashforge Creator Pro filament guide tubes, keeping their ends at a safe distance from the printer case to prevent entanglement and positioning them at an angle that complements the superior Makerbot acrylic dome.

I bought a Flashforge creative pro 3D printer in 2017 to handle filament more efficiently. Different diameter spools can be secured with the rear-facing filament holder on this printer. The filament alignment bridge helps prevent knots from...

ServiceTray for FlashForge Creator Pro 2016 fits perfectly into the top hole on this machine, making maintenance of the extruder, fans and nozzles much simpler. This useful accessory is designed to be printed as a single piece, but an alternative...

GoPro Mount for Flashforge Creator Pro. Two arm lengths are available, 45mm and 60mm. This mount will hang from the front of the printer, with a hump in the middle to fit over the screw. (This is designed specifically for those who paid $1,200;...

This customizable guide is specifically designed to secure Flashforge Creator Pro filament tubes. It elevates tube ends away from printer casing, preventing entanglements and optimally positioning them within the superior Makerbot acrylic dome found...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

So I had to purchase the only lid FlashForge provides for the 2016 creator pro, which is the unibody lid. If you're not aware, this lid is 12mm too short to sit properly on top and there are no brackets to secure it in place. As a result, here's my...

A perfect companion for the replacement filament tube holder, this replacement for the Creator Pro 2020 standard spooler was created to remedy two of its flaws: (a) On the standard spooler, the flexible clips used to remove the spool are hard to...

Printer Settings: * Printer: FlashForge Creator Pro * Rafts: No * Supports: No * Resolution: 0.3 * Infill: 25 Post-Printing Assembly: Insert the Inside Clamp.stl from within the printer, ensuring it aligns flush with the back of the device. Next,...

Print Settings: Printer: FlashForge Creator Pro Rafts: No Supports: Yes Resolution: 0.20 or less Infill: 25% - 100% Notes: When printing the hanger and knurled knob, add a G-code command to pause the print just before covering the captive nut hole...

Here's a link to that little handle: http://www.thingiverse.com/thing:1241895 My Print Settings Printer - I used the Flashforge Creator Pro, a great printer. Rafts - I didn't need any rafts for this thing. Supports - My printer could handle some...

The spool holders that come with the FlashForge Creator Pro (2016 version) are very limited in the dimensions of spools that it can hold. Most of my spools are either too wide or the hub is too small to fit on the manufacturer's holders. So I made a...

The spool holders provided with the FlashForge Creator Pro (2016 version) have very limited dimensions, unable to accommodate most of my spools. Either they're too wide or their hubs are too small to fit on the manufacturer's holders. As a result, I...

Print Settings: Printer Brand: FlashForge Printer: Creator Pro Rafts: No Supports: Doesn't Matter Resolution: 0.2 mm Infill: 14% Filament: Renkforce ABS Black Post-Printing: If the holes come out too small, use a 3 mm drill for the screw holes and...

This is meant to be a full ventilation kit for a Flashforge Creator Pro. You will need to print: -Top Replacement pieces for FFC Pro: FFC PRO Vent Top Left and Right (2 pieces total) -Duct to mount to top of new FFC Pro Top: 4in Vent adapter from...

Weiterentwicklung des Filament Wandhalters, zu dem Ersatzhalter für den Falaschforge, Creator Pro /2

This Thing offers both a replica of the top plate of the 2016 FlashForge Creator Pro (unsure whether this is different on older models), and an improved version (‘v2’ suffix). This is the part that connects the umbilical cord and the filament guide...

This is the 2mm shim required when adding a flexible build plate to the Flash Forge Creator Pro 2

Mount for the Paneldue i5, it is made to replace the original LCD display of the Creator Pro 2016 and uses the same screws.

These custom-made glass plate bed clips are designed specifically for the 1/4-inch borosilicate glass that FlashForge USA sells online. The clips I created use ABS filament as their material. My main goal was to create an easier alternative to...

I created this to make swapping spools easier without struggling with the holder on the Flashforge.\r\nYou simply need a base plate and print adapters for your spools, which can be left attached to an adapter, allowing you to hang them from the wall...