flashforge adventurer 3 upgrades 3d models

Fits all tools included with the machine + one extra tool for the bowden pipe nut (Single head open wrench size 10mm, regular IKEA tool most people have at home).

This is a tool holder that I designed to hold all my tools I use. It holds: 2" putty knife/scraper Glue Stick USB Stick Stylus Nozzle Cleaner Small Screwdriver Small hex key I affix it with double sided gorilla tape and mount on the back...

FlashForge Adventurer 4 Fan Mod

The active carbon purifies unpleasant odours and all kinds of waste.I use a Flashforge Adventurer 3 at work and it has a 40mm extractor fan on it that's mounted into a metal panel. You can buy an official Flashforge product that fits it with magnets,...

The Voxel / Adventurer 3 redesigned its internal spool holder around March or April, 2020, and this has an enlarged base to fit that. Two things: The model needs to be repaired in Flashprint -- just let it do its thing. Second, the base is VERY...

This is an adapter for newer versions of the Flashforge Adventurer 3, designed to slide seamlessly into the center pin of the existing mount. Its versatility allows it to adapt perfectly to +50mm spool center sizes. ...I incorporated a hinge to enable...

I made this mount to work with an Arducam USB camera, It clips onto the right side of the touchscreen controller on a Flashforge Adventurer 5M.

I made this mount to work with an Arducam USB camera, It clips onto the right side of the touchscreen controller on a Flashforge Adventurer 5M.

A replacement (or additional) bowden tube/ribbon guide for the Flashforge Adventurer 4 & Adventurer 4 Lite. Simple print, and should take less than 10 minutes to print. ... I printed this on the Adventurer 4 Lite, but that option is not availabe in the...

This filament roll extender allows you to use the standard-size filament roll which is too big for the FlashForge Adventurer 3 filament compartment. How to use: open the filament compartment bay door and clip the extender onto the original...

This print is a single layer test print designed to surface levelling issues on your Flashforge Adventurer 4. The design is 220mm x 200mm to fit the entire printable area of the ADV4.The ADV4 has a 9-point bed levelling system that does not provide...

Because of the way the Adventurer 5M feeds filament up from below, I found that my original design was too high up on the printer, especially when the spool starts getting low.It is designed to be screwed onto the top of the machine using two screws...

The key to levelling the Adventurer 3 and Adventurer 4 printers successfully is getting it as trammed as best as possible with shims and/or tape. I watched many videos showing this, but none had a good tool to judge the tramming. I decided I...

I found it much easier to use a handle to open the door the Adventurer 4 than the normal design so i designed a simple door handle.This simple slides onto the door for a snug fit and there is no gluing or assembly required.

A few months later I created and uploaded a similar design for the larger and quieter Noctua NF-A9x14 fan (92x92x14mm - it may or may not fit into your printer) - make sure to check out that alternative too before you settle on a...

Not a remix per se, since I did it from scratch, but I used measurements of madsqlj I made it printable on adventurer 3 bed with screw joints. ...I also recommend gluing some sort of filter on the grill Needs some short m3 screws and nuts besides...

Previous ones did not have the back clips that the original Flashforge one had to keep the air duct (and things above it) in place, nor did they have the original's inner air pipe. This model has both. I tested it - went in nicely and the PLA test...

Redesigned the fan adapter from moritzrath (https://www.thingiverse.com/thing:4543361) to make room for the fan cable. Also increased the hole size to 5mm to make fitting the rubber holders easier. ... For mounting instructions and parts see:...

Hello everyone, as some other people already mentioned, the filament touches the spool imo too much with the basic guide - so i created this version of it. ...I haven't printed it yet, feel free to comment and criticize

I wouldn't make a hole into the door to use filament from outside But my door is very simple. That is much much much better! ...;) https://www.thingiverse.com/thing:3419993 or https://www.thingiverse.com/thing:3329107 or ...

Print at 100% infill with 4 walls, and no parts cooling the first three layers. ...

Hello! This is a small piece of plastic that can be placed in front of printing bed to add more support for the flexible plate. In my experience hinge that keep flexible plate in place is pretty weak and does not provide much support, so when...

Set consists of a bracket with which you can mount a 4mm Push-in coupling under the feeder. The hole is 5 mm and M6 thread has to be cut with a tool. For the adapter a hole has to be cut in the door. I have fixed the adapter in the door with some...

Having used the original spool holder (https://www.thingiverse.com/thing:4002193), after a couple of months it slowly bowed and broke under the weight of 1KG spools. ... I have added a support to take the weight of larger spools.

Filament guide to allow the original door to be closed with an external spool. Cut the door hole opening to 11x65 mm, then glue this insert to door when done and after testing it out. ... See the red rectangle on the picture for rough placement.

I have modified the factory flexible plate to use a magnetic PEI plate, but my Y-Axis Has been slipping. After several iterations I was able to make this clips that keep the plate from sliding forward. This should be helpful for anyone using...

I modified the SpoolHolder_v8 so I could use wider spools such as Amazon Basics brand.

Remix of madsqlj model. ...While the model is spot on it bends over time and is prone to breakage, i reinforced the latch so it can be printed stronger so it does not bend and without supports.

Add a lid to the open part of cover Please print the following cover first https://www.thingiverse.com/thing:3184595 The lid is divided into an top side and a bottom side, and the two are connected for use. * Adv3cc_top.stl x 1 The top...