flashforge adventurer 3 auto calibration 3d models

Diseño 3D por Jesús RamírezMándame un mensajito si necesitas algún Diseño

This is a remix of the filament guide from underhill. Changed for the 2020-2021 model of which the screw is placed a bit higher. I rebuilt it so the ptfe-tube sits tightly, but can still easily be removed when using the internal spool. For this i...

This hooks onto the back of the printer, slotting in-between the grills at the back of the printer. I use large filament spools and need to remove the cover most of the time. When the cover is not attached to the printer, it can be safely stored at...

This is a remake for the cable management system. I attempted to utilize the original setup but encountered difficulty in removing or installing it without dismantling the entire printer assembly. ...Consequently, I designed this remake and employed...

Add a lid to the open part of cover Please print the following cover first https://www.thingiverse.com/thing:3184595 The lid is divided into an top side and a bottom side, and the two are connected for use. * Adv3cc_top.stl x 1 The top...

This remix optimizes the design so less support is needed. Only inside the fitting hole needs to be supported. ...I also tweaked the model a bit so it prints a bit faster.

Unsure if anyone else has this issue, but the left Z axis lead screw was rattling and had a lot of play for me, so this bracket stops that. To install you take the top cover off and undo the 2 screws holding the metal bracket to the case, then lift...

I modified the SpoolHolder_v8 so I could use wider spools such as Amazon Basics brand.

Having used the original spool holder (https://www.thingiverse.com/thing:4002193), after a couple of months it slowly bowed and broke under the weight of 1KG spools. ... I have added a support to take the weight of larger spools.

Made this to save the wear on the tube due the movement experienced without a support.

I wouldn't make a hole into the door to use filament from outside But my door is very simple. That is much much much better! ...;) https://www.thingiverse.com/thing:3419993 or https://www.thingiverse.com/thing:3329107 or ...

Remix of madsqlj model. ...While the model is spot on it bends over time and is prone to breakage, i reinforced the latch so it can be printed stronger so it does not bend and without supports.

Redesigned the fan adapter from moritzrath (https://www.thingiverse.com/thing:4543361) to make room for the fan cable. Also increased the hole size to 5mm to make fitting the rubber holders easier. ... For mounting instructions and parts see:...

I have modified the factory flexible plate to use a magnetic PEI plate, but my Y-Axis Has been slipping. After several iterations I was able to make this clips that keep the plate from sliding forward. This should be helpful for anyone using...

i made it for test my Flashforge 3D printers, this file is same like Voron cube, Size is 30x30x30mm.Enjoy!!!!!!!!!!!!!

... a New Internal Spool Wheel Design for the Printer. Additionally, an Adapter Was Added for the New Hose Wheel. Original File Link: Https://Www.creativetools.se/Misc/Doc/Flashforge/Adventurer-3/Extended-Spool-Holder-for-Adventurer3-Stl.Stl

I crafted an adapter specifically designed to fit snugly inside the FlashForge Adventure 3, accommodating their unique size filament spool which is smaller than a standard 2.2 Lb. spool. ...This thoughtful design prevents any wear on the machine's...

Logitech C270 camera mount for Flashforge Adventurer 5M

Official FlashForge Adventurer AD5M Spool holder, removed "LXD" logo.

Spool holder for the adventure 3 ( year 2021).

Flashforge Adventurer 9pt Bed Level Test - Use this to help yourself level the bed

This replacement piece holds the auto leveling sensor securely in place for the Flashforge Finder. The factory size is included, but I've also added a Sketchup file so you can modify it if needed. ... Print Settings: Printer: Flashforge Creator Pro...

This is a custom replacement part designed to secure the auto leveling sensor within the Flashforge Finder 3D printer. The component comes pre-assembled with dimensions matching those of the original factory-produced item. ...Additionally, I have...

An external filament feed cover for the Monoprice Voxel / Flashforge Adventurer 3 with a Bowden Tube adapter. Cut a hole in the door using a heated knife, place the printed part and seal with a glue gun. The model’s bottom left position from the...

The plate model from Adventurer 4 is taken as a basis. ...Cut in a slicer, duplicated and mirrored. Combined and glued in a Flashforge slicer similar to the 4Pro Extruder plate.

Their are two version to select from, both work with plastic/cardboard spools.v.1 40mm x 82mm cylinder with 2.0mm edge universal spoolsv.2 50mm x 82mm cylinder with 2.0 edge sized for FlashForge 53mm spools.Printed on FlashForge Adventurer 4...

A drop-in replacment for Flashforge Adventure 4 fan duct. ...Print the two parts in PTEG or ABS an glue together with super glue.&nbsp;</p><p>&nbsp;</p><p>Remix from https://www.thingiverse.com/thing:5244614&nbsp;</p><h3>&nbsp;</h3><p>&nbsp;</p>

The touch screen that comes with the Flashforge Adventurer 5M Pro appears to be more responsive if you use a a tablet pen. I designed a pen holder based on this spool holder design: https://www.thingiverse.com/thing:6286294. Alibre Atom was used to...

I have mirrored the file, extended the segment for the catch(duct side) and increased the height of the opening of the fan duct fo fit the Flashforge Adventurer 4. I am currently printing a test version and will try to fit it on my AD4 once i...

Modeled off the Adventurer 3 nozzle, I have modified the dimensions to fit the adventurer 4, but included a solid mount to add a depth gauge to measure the bed imperfections.