flash forge creator pro 3d models

All of the door open clips I used for my Creator Pro snapped or warped whenever the door swung open, which was frustrating. I decided to create a custom solution and ended up using this one, which has proven to be incredibly reliable. ...To use it,...

... filament in them. ... Print Settings Printer: Flashforge Creator Pro Rafts: Disabled Supports: Disabled Resolution: 0.2 mm Infill Percentage: 20% Post-Printing Instructions Inspect the print and lightly sand any parts that are too tight for a snug fit.

I've designed these filament holders for the Flashforge Creator Pro 2 that i have. these are under an angle to keep your filament roll on it. there are several options to choose from here. 20mm, 30mm, 40mm and 50 mm with a small angle and...

FlashForge Creator Pro users can now breathe a sigh of relief as the innovative Bowden holder prevents the pesky tube from pressing against the extruder, thereby solving one of the most frustrating problems with extrusion that has plagued them for...

https://www.thingiverse.com/thing:4828718 This mount is created for problems of Creator Pro users with different filaments like Polaroid. By using three/two screws you can simply fix the parts. ... *Three M2.5-1 to 1.5 screws is required.

https://www.thingiverse.com/thing:4828718 This mount is created for problems of Creator Pro users with different filaments like Polaroid. By using three/two screws you can simply fix the parts. ... *Three M2.5-1 to 1.5 screws is required.

I modified the drain cleaner design from jmsaltzman to make it compatible with a FlashForge Creator Pro. To print it successfully, place the model at a 30-degree angle so that it prints diagonally across the bed. ...Although it printed well and should...

... surface. ...Issues arose with extruder contact since the glass I'm working with is thinner than what those clips were initially engineered for. Printer Settings Printer: FlashForge Creator Pro Rafts: No Supports: No Resolution: .2 Infill: 30% Notes:

http://www.thingiverse.com/thing:976727 The new Creator Pro has moved its limit switch to the left, which means the old Creator Pro shim will no longer fit. To compensate for this change, a block of material was added and a contour cut out to match...

I just picked up a fresh spool of AMZ3D filament designed specifically for use with the FlashForge Creator Pro, boasting a 1.25 inch diameter. ...With the upgrade in mind, I took matters into my own hands and crafted a custom spool holder tailored to...

This spool holder mounts directly onto the rear of a Flashforge Creator Pro, accommodating spools up to 1 centimeter in diameter. ...Included with this design is the original .ipt file, allowing users to easily modify the dimensions as needed for their...

The vulnerable spot of the SD card slot on my FlashForge Creator Pro is a major concern, prompting me to craft a protective cover for it. I used 1.75mm filament as the pivot point for the hinge. ...To secure it in place, I employed a combination of...

These are a pair of different grommets designed specifically for the base of the Creator Pro, tailored to accommodate the hole through which cables for the HBP pass to the motherboard. The ones I previously downloaded needed additional supports and...

The IGUS polymer bearings take the place of an LG8UU, a bearing that measures 24mm in length, while the Creator Pro utilizes the LGSUU, which stands at 17mm. ...This precision jig enables you to accurately cut down the 24mm to fit the 17mm dimension and...

The FlashForge Creator Pro's Z Axis Guard Plate Has Been Reverse Engineered. Using the Original Plate as a Blueprint, I Successfully Replicated It Even After It Cracked. The Model Was Created Using UG NX Software with Great Attention to Detail. ... As...

I designed this spool holder because the vanilla spool holders were not working very well for the Flashforge Creator Pro. These work like a charm. ...The footprint is quite large, so I highly recommend printing with a raft to help minimize over-adhesion...

... access and management. ...When opting for a wall-mounted custom spool holder like mine, it becomes an essential accessory due to the Flashforge Creator Pro's standard large spool holders, which often fail to accommodate most spools from other brands.

Another accessory tailored specifically for users who've upgraded their Flashforge Creator X with a backfit, incorporating the metal build platform from the Creator Pro. This shim should fit perfectly on numerous machines that employ a similar...

To see just how well this spool performs, check out our demonstration video: https://youtu.be/Yx6WwHR1QlI Here are the print settings we used: * Printer: Creator Pro * Rafts: Not necessary * Supports: Yes * Resolution: 200 microns * Infill: 30% *...

... require more complex printing, necessitating supports, etc. I did use a raft because the base is very thin, but trimming the end would likely allow printing without it. Printer settings: Printer: Flashforge Creator Pro Rafts: Yes Supports: No

Go here: https://www.extra-life.org/participant/385519 This is a direct-drive adapter that will fit the FlashForge Creator Pro printer with the E3D Cyclops extruder. WARNING: Do not perform this upgrade on your primary or sole 3D printer. It is...

Seeking a broad field of view without obstruction for the Creator Pro, this cam should suffice. It likely works with similar printer designs. M3 bolts and nuts (45mm long) are required for the arm mount. Gorilla double-sided tape secures it to the...

This tool has been specifically designed to hold both cooling blocks steady while you loosen the nozzle, making the process much smoother and more efficient.\nLet me know if this fits your machine just right.\nThanks for taking a look at it.\nPrint...

... something special for itself? Print Settings Printer: FlashForge Creator Pro Rafts: Yes Supports: Yes Resolution: 0.1mm Infill: 100% Notes: These are the settings I used but hey, feel free to experiment. ...I prepped the gcode with Simplify 3D.

Print Settings Printer: Creator Pro Rafts: No Supports: No Infill: =30% Post-Printing Installation .266-inch holes included for easy installation of 1/4-20 Helicoil inserts. After insertion into the handle slot, fasten with a 1/4-20 (1/4-inch...

Summary Mount for Flashforge Creator Pro (and probably all MakerBot clones) Smart camera available on AliExpress: http://www.aliexpress.com/item/Sricam-SP009-Wireless-IP-Camera-WiFi-HD-720P-indoor-1-0MP-P2P-720P-Video-IR-Network/32603411551.html...

This is a revamped version of Seamongrel's FlashForge Creator Pro 2016 Lid Holder, tailored to utilize one single 3/4" ceramic disc magnet. I opted for an "ook" brand magnet from Walmart, which measures approximately 18mm in diameter by 5mm thick.

This simple filament spool hanger was designed to fit on a Flashforge Creator Pro (or Flashforge Creator Pro 2). They fit in the slots on the back where the stock hangers go. The stock hangers were not long enough or small enough diameter for some...

After discovering that pre-existing designs for filament tube holders wouldn't fit inside my new FlashForge Creator Pro, I made the decision to create my own design.\nThis is the second version, designed entirely from scratch! The piece's dimensions...

... about 1" off the length of the filament guide tubes that are provided with the printer. Print Settings Printer: Flashforge Creator Pro Rafts: Yes Adhesion Type: Magigoo Supports: No Resolution: High/Slow Layer Height: 0.2mm Infill: Medium - 30%